Labor protection instruction for a water supply electrician

Free technical library

OCCUPATIONAL SAFETY AND HEALTH
Free library / Occupational Safety and Health / Standard instructions for labor protection

Instructions on labor protection for a water supply electrician. Full document

Occupational Safety and Health

Occupational Safety and Health / Standard instructions for labor protection

Comments on the article

Safe Operation

1. General requirements for labor protection

1.1. Persons at least 18 years of age who have passed a medical examination, special training, practical training, have an electrical safety group, and have also passed:

introductory and primary briefings;
fire safety briefing;
: repeated briefing at the workplace;
unscheduled and targeted briefings;
internship.

1.2. An electrician for the repair of electrical equipment of a water supply section, when independently performing work on electrical installations with a voltage of up to 1000 V, must have at least safety group III, and more than 1000 V - group IV.

1.3. In the course of work, within the time limits set at the enterprise, the electrician of the water supply section must undergo safety briefing, coursework for an 18-hour program and pass exams on knowledge of the rules for the technical operation of consumer electrical installations and safety regulations for the operation of consumer electrical installations.

1.4. The mechanic for the repair of electrical water supply equipment must know the terms for testing protective equipment and devices, the rules for operating and caring for them, and be able to use them. It is not allowed to use protective equipment and devices with an expired test period.

1.5. The electrician of the water supply section who uses lifting mechanisms, electric and pneumatic tools, grinding and drilling machines in the course of their main work, as well as performing work associated with increased danger and harmfulness, must undergo additional training, pass the technical minimum for the device and operation of this equipment , tools, briefing on the rules for the safe performance of work, and have an appropriate certificate.

1.6. The paints and varnishes used in the work and their solvents should be stored in rooms with reliable ventilation and well-closing metal doors, due to their explosiveness and toxicity.

Containers for storing paints and varnishes and their solvents must be tightly closed. The tool for opening and closing containers must be explosion-proof.

1.7. The water supply electrician must know and comply with safety requirements.

1.8. An electrician during work should use the following PPE: cotton suit, leather boots, dielectric gloves and galoshes, goggles.

1.9. After working with varnishes and their solvents, wash your hands with warm water and soap.

An electrician for the repair of electrical water supply equipment who violates labor protection requirements is held liable in accordance with the job descriptions established for each employee in accordance with the current legislation of the Russian Federation.

1.10. Each employee, in accordance with Article 8 of the Federal Law "On the Basics of Occupational Safety in the Russian Federation", has the right to refuse to perform work without any unreasonable consequences for him in the event of an immediate danger to his life and health until this danger is eliminated.

2. Labor protection requirements before starting work

2.1. The electrician for the repair of electrical water supply equipment must check:

overalls, put them in order, fasten the cuffs of the sleeves;
pick up hair under a tight-fitting headdress;
whether the workplace and approaches to it are sufficiently lit, the light should not blind the eyes;
serviceability and fastening of the vise and adjust their height in accordance with their height by laying in front of the workbench (under the feet) a special wooden lattice or stand of the required height so that the surface of the vise is at the level of the elbow joint. Bench vise and clamps should not have play, firmly grip the clamped products and have an unworked notch on the jaws;
hand tools and accessories necessary for work, personal protective equipment should be laid out in convenient and easily accessible places to exclude the possibility of accidental movement or falling during work.

2.2. Inspect and tidy up the workplace, remove everything that may interfere with work; if the floor is slippery (doused with oil, paint, water) demand that it be wiped or do it yourself.

2.3. When working, use only serviceable, dry and clean tools and fixtures; the blade of the screwdriver must be retracted and flattened to such a thickness that it enters without a gap into the slot of the screw head;

wrenches must match the dimensions of the nuts and bolt heads and must not have cracks, gouges, burrs. The jaws of the keys must be strictly parallel and not rolled up. Sliding keys should not have slack (play) in moving parts;
needle nose pliers and pliers should not have chipped, broken jaws, handles. The jaws of the needle nose pliers must be sharp, and the pliers must be properly notched;
supports used in manual riveting, crimping, chasing and other work must be strong and safe;
pullers must have a rigid structure and not have cracks, bent rods, stripped or crumpled threads and ensure the tolerance of the thrust (tension) device with the axis of the part to be removed. Puller grips must provide a tight and secure grip on the part at the point of application of force. Locksmiths are required to comply with the requirements for handling tools established by the factory instructions.

2.4. To carry the tool, the worker should use a special bag or a lightweight portable box. Carrying tools in pockets is prohibited.

2.5. When using lifting mechanisms (hoists, hoists, etc.), check the reliability of their fastening. Make sure that the lifting mechanisms and their lifting devices are in good condition.

2.6. If a malfunction of equipment, tools, accessories for the workplace is detected, both before starting work and during work, inform the foreman and do not start work until the troubleshooting. Defective tools must not be used.

3. Labor protection requirements during work

3.1. In the course of work, the water supply electrician is obliged to:

perform only the work assigned by the administration. If the safe way of performing the work is not well known, contact the administration for clarification;
do not start a new (unfamiliar) work of the receiving bases from the master instructing about safe ways to do it;
keep your workplace clean and tidy during the entire working time, there should be no oil, parts, blanks, scraps and other waste under your feet; during work, be attentive, not be distracted and not distract others;
do not allow persons related to this work to the workplace. Without the permission of the master, do not trust your work to another worker;
noticing a violation of the instructions by other workers or a danger to others, do not remain indifferent, but warn the worker about the danger or the need to comply with safety regulations.

3.2. Before removing electrical equipment for repair, remove the voltage in the network at least in two places, and also remove the fuses. Proceed with the removal of electrical equipment only after checking the absence of voltage and posting the poster "Do not turn on. People are working" on the switch or control key.

3.3. For lifting, removing, installing and transporting heavy (weighing more than 16 kg) units, assemblies and parts, you must use serviceable lifting and transport equipment of the appropriate carrying capacity, on which you are allowed to work.

3.4. When working with hoisting mechanisms, follow the requirements of the labor protection instructions for persons using hoisting mechanisms operated from the floor.

3.5. Disassembly and assembly of small units of electrical equipment should be carried out on workbenches, and large-sized ones - on special work tables or stands, cassettes that ensure their stable position.

3.6. Wrenches should only be used according to the size of the nuts or bolts. When tightening or loosening nuts or bolts, do not install a lining between the edges of the wrench and nut, as well as use levers.

3.7. When removing, pressing and pressing plug-in units and parts, use pullers, presses and other devices that ensure safe operation.

3.8. When working at a workbench, make sure that its surface is clean, smooth and free from burrs.

3.9. Clamp the workpiece securely in a vise. When installing in a vise, handle heavy parts carefully to avoid bruising when they fall.

3.10. When cutting, riveting, chasing and other similar work, in which metal particles may fly off, use glasses or a mask with safety glasses.

3.11. When disassembling electric motors, shields, stators, rotors and anchors should be placed on special racks and stands.

3.12. Welding or soldering of the ends of the windings should be carried out only in protective glasses.

3.13. Before testing electrical equipment after repair, it must be firmly fixed, grounded (zeroed), and rotating and moving parts are closed with safety covers.

3.14. When performing work jointly with several persons, a senior (link) worker must be appointed, who is obliged to coordinate the actions of workmates.

4. Labor protection requirements in emergency situations

4.1. In case of any accident or an emergency situation that can lead to an accident and an accident, the water supply electrician is obliged to immediately take all measures in his power to prevent the possibility of damage (destruction) of the object and eliminate the danger to people's lives. At the same time, report the incident to the foreman or immediate supervisor of the work.

4.2. In order to avoid emergency situations, use only serviceable load-lifting mechanisms.

4.3. Repair of electrical equipment should be carried out only when the voltage is removed.

4.4. Each worker must be able to provide first aid. Such assistance is provided immediately, directly at the scene and in the following sequence:

First you need to eliminate the source of injury. Assistance should begin with the most significant that threatens health or life: in case of severe bleeding, apply a tourniquet, and bandage the wound with a son-in-law; if a closed fracture is suspected, apply a splint;
with open fractures, you should first bandage the wound, and then apply a splint;
in case of burns, apply a dry bandage; in case of frostbite, gently rub the affected area using soft or fluffy tissues;
in case of electric shock, it is necessary to immediately release the victim from the action of the current, namely: turn off the switch, cut the wire, pull or discard it with a dry stick, pole. Do not touch the victim while he is under the influence of current. If the victim is not breathing, then immediately start a heart massage and artificial respiration until the doctor arrives.

4.5. After providing first aid, the victim should be sent or taken to the nearest medical facility.

5. Labor protection requirements at the end of work

5.1. Disconnect (disconnect) electrical equipment, power tools, lifting machines from the network.

5.2. Store tools and accessories in the designated storage area.

5.3. Drain the remains of varnishes and solvents into a special tightly closed container.

5.4. Tidy up the workplace, put it in a metal box with a lid or destroy the rags used during work.

5.5. Wash hands with warm water and soap.

5.6. Report any problems found during operation to the foreman.

We recommend interesting articles Section Standard instructions for labor protection:

▪ Working with an electric chain saw. Standard instruction on labor protection

▪ Woodworking machine operator. Standard instruction on labor protection

▪ Work on a book-inserting machine type B-3, etc. Typical instructions for labor protection

See other articles Section Standard instructions for labor protection.

Read and write useful comments on this article.

<< Back

Latest news of science and technology, new electronics:

Artificial leather for touch emulation 15.04.2024

In a modern technology world where distance is becoming increasingly commonplace, maintaining connection and a sense of closeness is important. Recent developments in artificial skin by German scientists from Saarland University represent a new era in virtual interactions. German researchers from Saarland University have developed ultra-thin films that can transmit the sensation of touch over a distance. This cutting-edge technology provides new opportunities for virtual communication, especially for those who find themselves far from their loved ones. The ultra-thin films developed by the researchers, just 50 micrometers thick, can be integrated into textiles and worn like a second skin. These films act as sensors that recognize tactile signals from mom or dad, and as actuators that transmit these movements to the baby. Parents' touch to the fabric activates sensors that react to pressure and deform the ultra-thin film. This ... >>

Petgugu Global cat litter 15.04.2024

Taking care of pets can often be a challenge, especially when it comes to keeping your home clean. A new interesting solution from the Petgugu Global startup has been presented, which will make life easier for cat owners and help them keep their home perfectly clean and tidy. Startup Petgugu Global has unveiled a unique cat toilet that can automatically flush feces, keeping your home clean and fresh. This innovative device is equipped with various smart sensors that monitor your pet's toilet activity and activate to automatically clean after use. The device connects to the sewer system and ensures efficient waste removal without the need for intervention from the owner. Additionally, the toilet has a large flushable storage capacity, making it ideal for multi-cat households. The Petgugu cat litter bowl is designed for use with water-soluble litters and offers a range of additional ... >>

The attractiveness of caring men 14.04.2024

The stereotype that women prefer "bad boys" has long been widespread. However, recent research conducted by British scientists from Monash University offers a new perspective on this issue. They looked at how women responded to men's emotional responsibility and willingness to help others. The study's findings could change our understanding of what makes men attractive to women. A study conducted by scientists from Monash University leads to new findings about men's attractiveness to women. In the experiment, women were shown photographs of men with brief stories about their behavior in various situations, including their reaction to an encounter with a homeless person. Some of the men ignored the homeless man, while others helped him, such as buying him food. A study found that men who showed empathy and kindness were more attractive to women compared to men who showed empathy and kindness. ... >>

Random news from the Archive

NVIDIA began to assemble some video cards on its own 26.11.2010

NVIDIA has announced certain changes to its policy.

If earlier it only provided third-party assemblers with reference models that could be used to design accelerators with a similar cooling system and other design elements, now NVIDIA intends to produce video cards on its own production lines.

Other interesting news:

▪ New camera series from CANON

▪ Underground art gallery

▪ Sony SDM-HS73P - new monitor with Onyx-black technology

▪ Bioactive coating for bone implants

▪ Microbes recognize letters

News feed of science and technology, new electronics

Interesting materials of the Free Technical Library:

▪ section of the site Electronic directories. Article selection

▪ article And gave him neither rest nor time. Popular expression

▪ article Why is there no life on other planets? Detailed answer

▪ article dosimetrist. Job description

▪ Article Toilet Vinegar. Simple recipes and tips

▪ article Mixer (nodes of a modern transceiver). Encyclopedia of radio electronics and electrical engineering

Leave your comment on this article:

All languages of this page

Home page | Library | Articles | Website map | Site Reviews