Occupational safety instructions for a plastics presser

Free technical library

OCCUPATIONAL SAFETY AND HEALTH
Free library / Occupational Safety and Health / Standard instructions for labor protection

Occupational safety instructions for a plastics presser

Occupational Safety and Health

Occupational Safety and Health / Standard instructions for labor protection

Comments on the article

Safe Operation

1. General safety requirements

1.1. Individuals who have passed a medical examination are allowed to work independently as a plastic presser, as well as:

induction training;
fire safety briefing;
initial briefing at the workplace;
training in safe working methods and techniques for at least 10 hours;
instructing on electrical safety at the workplace and checking the assimilation of its content.

1.2. The plastics presser must pass:

repeated briefing on labor safety at the workplace at least every three months;
unscheduled and targeted briefings when changing the technological process or labor protection rules, replacing or modernizing production equipment, fixtures and tools, changing working conditions and organization, in case of violations of labor protection instructions, breaks in work for more than 60 calendar days (for work, which are subject to increased security requirements - 30 calendar days);
dispensary medical examination according to the order of the Ministry of Health of the Russian Federation No. 90 dated March 14, 1996

1.3. The plastics presser must:

comply with the internal labor regulations established at the enterprise;
comply with the requirements of this manual, fire safety instructions, electrical safety instructions;
comply with the requirements for the operation of equipment;
use for its intended purpose and take care of the issued personal protective equipment.

1.4. The plastics presser must:

be able to provide first (pre-medical) assistance to the victim in an accident;
know the location of first aid, primary fire extinguishing equipment, main and emergency exits, evacuation routes in case of an accident or fire;
perform only the assigned work and not transfer it to others without the permission of the foreman or head of the workshop;
during work, be attentive, not be distracted and not distract others, do not allow persons who are not related to work to the workplace;
keep the workplace clean and tidy.

1.5. The plastics presser must know and follow the rules of personal hygiene. Eat, smoke, rest only in specially designated areas and places. Drink water only from specially designed installations.

1.6. If any malfunctions of equipment, fixtures, tools and other shortcomings or hazards are found in the workplace, immediately inform the foreman or head of the workshop. You can start work only with their permission after the elimination of all deficiencies.

1.7. If a fire is detected or in the event of a fire:

turn off the equipment;
inform the fire brigade and administration;
start extinguishing the fire with the primary fire extinguishing equipment available in the workshop in accordance with the fire safety instructions.

In case of a threat to life - leave the premises.

1.8. In case of an accident, provide the victim with first (pre-medical) aid, immediately report the incident to the foreman or head of the workshop, take measures to preserve the situation of the incident (equipment condition), if this does not create a danger to others.

1.9. For non-compliance with the safety requirements set forth in this manual, the presser is liable in accordance with applicable law.

1.10. In accordance with the "Model Industry Standards for the Free Issue of Special Clothing, Special Footwear and Other Personal Protective Equipment to Workers and Employees", a plastics presser must use the following PPE: cotton suit, leather boots, combined gloves.

1.11. The main hazardous and harmful production factors under certain circumstances can be:

elements of production equipment;
faulty working tool;
flying plastic particles;
electric current;
increased gas content in the air of the working area;
industrial noise.

1.12. A press operator who has violated the requirements of the labor protection instructions may be subject to disciplinary liability in accordance with the internal labor regulations

2. Safety requirements before starting work

2.1. Before starting work, the plastics presser must put on working clothes and safety shoes that meet the standards, put them in order, button up the cuffs of the sleeves.

2.2. Check your workplace, it should be evenly lit (no glare), not cluttered with foreign objects.

2.3. Check at idle the readiness of the equipment for operation and at the same time make sure that the control mechanisms are in good condition, that the slider and guide presses move correctly, that all safety devices work reliably.

2.4. Make sure by external inspection that the grounding is available and in good condition, that the protective guards of the rotating parts of the equipment are available and in good condition.

2.5. Check the serviceability of tools and fixtures:

the locksmith's workbench must be free of potholes, cracks and other defects;
the handle of a percussion instrument (hammer, etc.) must be oval in cross section and straight;
the surface of the hammer head must be convex, smooth, not beveled, without burrs;
impact tools (chisels, crosscuts, barbs, etc.) must have a smooth occipital part without cracks, burrs, hardening and bevels;
the spindle of a hand tool with a pointed working end (files, screwdrivers, etc.) must be securely fixed in a smooth, smoothly cleaned handle, which, for greater strength, must be pulled together at both ends with metal bandage rings;
screwdrivers must be with non-curved rods, as the blade may slip off the head of the screw or screw and injure hands;
wrenches must correspond to the sizes of bolts and nuts, the jaws of wrenches must have strictly parallel jaws, the distance between which must correspond to the standard size indicated on the key;
socket and box wrenches must not move in the connected moving parts.

2.6. If it is necessary to use a portable lamp, check: the presence of a protective grid, the serviceability of the cord and insulating tube, the serviceability of the socket and plug. The voltage of portable lamps should not exceed 42 V. It is not recommended to use self-made portable lamps.

3. Safety requirements during work

3.1. Be attentive, do not be distracted by extraneous matters and conversations, do not distract others.

3.2. Check the correct adjustment of the protective grid in accordance with the height of the plane of the matrix or punch on the table, check the accuracy of the installation of matrices and punches in the absence of columns on the stamp.

3.3. Turn on the press for a working stroke only after the workpiece is correctly placed in the die, and the hands are removed from the danger zone.

3.4. The design of the die must ensure the stable position of the workpiece and the stable position of the die during its storage and transportation.

3.5. When moving the slider of the press, do not correct the workpiece, even if it is incorrectly laid, in this case quickly turn off the press.

3.6. When stacking blanks, removing stamped parts and waste using tweezers, hold the tweezers as close as possible to the end of the handle so that the hand is outside the danger zone of the stamp.

3.7. When laying workpieces and removing parts weighing 20 kg or more, use special lifting mechanisms.

3.8. When laying workpieces and removing parts from the die, do not keep your foot on the press switch pedal.

3.9. Make sure that the press pedal is protected and that the press does not turn on automatically due to parts or tools accidentally falling on it.

3.10. Turn on the start button or press pedal to failure, as careless turning on can cause a double stroke of the slider.

3.11. Laying workpieces in stamps should be carried out only when the slider is completely stopped in the upper position.

3.12. Do not make adjustments and corrections yourself while the press is in operation.

3.13. Lubricate the working parts of the stamp only with special brushes or devices for this purpose, lubricate with the press turned off.

3.15. Cleaning of waste and cuttings from the press should be carried out regularly and only with the engine turned off and the drive mechanism completely stopped.

3.16. During the operation of the press, do not open or remove covers, guards and safety devices.

3.17. Performing work jointly with several persons, coordinate their actions with the actions of other workers.

3.18. Do not touch the current-carrying parts of the equipment, electrical distribution boards, cabinets, general lighting fittings; do not step on portable electrical wires, hoses lying on the floor.

3.19. If the electrical equipment is faulty, call an electrician.

4. Safety requirements in emergency situations

4.1. In the event of an emergency, the plastic presser is obliged to stop work, immediately report the incident to the foreman (foreman) and then follow his instructions to prevent accidents or eliminate the emergency.

4.2. When eliminating an emergency, it is necessary to act in accordance with the emergency response plan approved by the depot.

4.3. In the event of a fire, notify the fire brigade and the supervisor

4.4. Extinguishing burning objects located at a distance of less than 2 m from the contact network is allowed only with carbon dioxide or powder fire extinguishers.

4.5. It is possible to extinguish burning objects with water, chemical, foam fire extinguishers only with the permission of the master, that the voltage has been removed from the contact network and it is grounded.

5. Safety requirements at the end of work

5.1. Disconnect the electric drive of the press.

5.2. Tidy up your workspace. Remove tools, attachments and lubricants to the place provided for them. Rags and flammable materials, in order to avoid spontaneous combustion, put in metal boxes with tight lids.

5.3. Inform the foreman about all the shortcomings that occurred during the work, and about the measures taken to eliminate them.

5.4. Take off overalls, put them in a closet, wash your hands and face with soap, take a shower if possible, and do not use chemicals for washing.

We recommend interesting articles Section Standard instructions for labor protection:

▪ Loading and unloading plant operator. Standard instruction on labor protection

▪ Guard worker. Standard instruction on labor protection

▪ Reception and shipment of milk. Standard instruction on labor protection

See other articles Section Standard instructions for labor protection.

Read and write useful comments on this article.

<< Back

Latest news of science and technology, new electronics:

Artificial leather for touch emulation 15.04.2024

In a modern technology world where distance is becoming increasingly commonplace, maintaining connection and a sense of closeness is important. Recent developments in artificial skin by German scientists from Saarland University represent a new era in virtual interactions. German researchers from Saarland University have developed ultra-thin films that can transmit the sensation of touch over a distance. This cutting-edge technology provides new opportunities for virtual communication, especially for those who find themselves far from their loved ones. The ultra-thin films developed by the researchers, just 50 micrometers thick, can be integrated into textiles and worn like a second skin. These films act as sensors that recognize tactile signals from mom or dad, and as actuators that transmit these movements to the baby. Parents' touch to the fabric activates sensors that react to pressure and deform the ultra-thin film. This ... >>

Petgugu Global cat litter 15.04.2024

Taking care of pets can often be a challenge, especially when it comes to keeping your home clean. A new interesting solution from the Petgugu Global startup has been presented, which will make life easier for cat owners and help them keep their home perfectly clean and tidy. Startup Petgugu Global has unveiled a unique cat toilet that can automatically flush feces, keeping your home clean and fresh. This innovative device is equipped with various smart sensors that monitor your pet's toilet activity and activate to automatically clean after use. The device connects to the sewer system and ensures efficient waste removal without the need for intervention from the owner. Additionally, the toilet has a large flushable storage capacity, making it ideal for multi-cat households. The Petgugu cat litter bowl is designed for use with water-soluble litters and offers a range of additional ... >>

The attractiveness of caring men 14.04.2024

The stereotype that women prefer "bad boys" has long been widespread. However, recent research conducted by British scientists from Monash University offers a new perspective on this issue. They looked at how women responded to men's emotional responsibility and willingness to help others. The study's findings could change our understanding of what makes men attractive to women. A study conducted by scientists from Monash University leads to new findings about men's attractiveness to women. In the experiment, women were shown photographs of men with brief stories about their behavior in various situations, including their reaction to an encounter with a homeless person. Some of the men ignored the homeless man, while others helped him, such as buying him food. A study found that men who showed empathy and kindness were more attractive to women compared to men who showed empathy and kindness. ... >>

Random news from the Archive

Computer view of art 22.12.2007

A program developed by Israeli scientists allows a computer to distinguish a genuine work of art from a fake.

Human vision has passed a long evolutionary path, computer vision is only in its infancy, it is no more than 30 years old. It is difficult for a machine to do something that is not difficult for us, for example, to see a person’s face in a photograph, to understand whether it is one or several images. But the computer easily builds three-dimensional images of the blood vessels of the brain or the road network.

Employees of the University of Haifa, under the leadership of Daniel Keren, created a program with which a computer can become a specialist in the field of painting. The program turns any picture - landscape, portrait, still life, genre scene - into a set of mathematical symbols, values of sines and cosines of angles.

Having recognized one or several works of the artist, the machine creates for itself the individual style of this author and in the future can identify him from other paintings that he has not seen before. According to Keren, the computer recognizes the work of a particular artist in different genres, completely different from each other. Having trained, in particular, on Dali's watch, the machine will always recognize his paintings, even those that we do not have watches.

"At this stage of development, the program is useful for beginners in the field of collecting, who are not always able to distinguish the original from the fake. As for the actual computer vision, work in this area is just beginning," Daniil Keren believes.

Other interesting news:

▪ HEVC hardware encoder

▪ Telescope to X-ray the Universe

▪ longest suspension bridge

▪ poisoned planet

▪ TDA8939TH - reference source for setting up a class D digital power amplifier

News feed of science and technology, new electronics

Interesting materials of the Free Technical Library:

▪ section of the site RF power amplifiers. Article selection

▪ article A comrade flies to a distant land. Popular expression

▪ article What is the main benefit of bees? Detailed answer

▪ article Road worker. Standard instruction on labor protection

▪ article Identification of conductors by colors or digital designations. Encyclopedia of radio electronics and electrical engineering

▪ article Scheme, pinout (pinout) of the Alcatel One Touch DB cable. Encyclopedia of radio electronics and electrical engineering

Leave your comment on this article:

All languages of this page

Home page | Library | Articles | Website map | Site Reviews