OCCUPATIONAL SAFETY AND HEALTH
Labor safety instructions for a mechanical assembly mechanic engaged in the manufacture of brackets for assembling the spring block frame. Full document Occupational Safety and Health / Standard instructions for labor protection Safe Operation 1. General requirements for labor protection 1.1. General safety requirements are set out in the Instruction "General safety requirements for professions and types of work in furniture production". 1.2. Hazardous production factors: moving machines and mechanisms, moving parts of production equipment; moving products, blanks, materials. Sources of factors: rotating parts of the machine, workpiece feeding mechanisms, sharp ends of wire, loose fastening of compressed air hoses. Effect of factors: possible injury to the worker in contact with the rotating parts of the machine, with the ends of protruding wire, metal strip or parts, and in case of possible breakage of hoses, the possibility of contact of the hands of workers with the working part. 1.3. Personal protective equipment: cotton suit; chrome boots with leather base; safety glasses; combined mittens. 2. Safety requirements before starting work 2.1. Verify:
2.2. If there is a device for automatically feeding a metal strip into the stamp and removing staples from the stamp, the working space of the press is fenced off to prevent access of hands to the danger zone. 3. Safety requirements during work 3.1. Install the coil of metal tape on the unwinding device only with the help of lifting mechanisms. The load specified for lifting equipment must not be exceeded. 3.2. Securely fasten the coil of metal tape to prevent it from falling off the hook when moving. 3.3. Release the coil of metal tape from the gripping devices only after installing it on the turntables or drum. 3.4. Before installing the coil, make sure that there are no protruding ends of the tape. 3.5. Be careful when inserting metal strip into the machine. Remove stuck staples from the stamp only using tweezers with the press turned on. 3.6. Monitor the serviceability of the hoses and their fastening at the connection points. 3.7. When unwinding the last turns of the tape from the turntable, install a special shield to prevent the end of the tape from being ejected. 3.8. Manufactured parts should be placed in special containers, on racks and in stacks. The height of the stacks should not exceed 1 m from the floor level. 4. Safety requirements in emergency situations 4.1. Turn off equipment. 4.2. Post a table about the malfunction of the machine or equipment and report this to the direct management. 4.3. In the event of a fire or extinguishing a flame, use a nearby fire extinguisher. 4.4. The victim or bystander must notify the appropriate work manager of each accident or poisoning. 4.5. The worker must be able to provide first aid. Such assistance is provided immediately, directly at the scene and in the following sequence: first you need to eliminate the energy source of injury (switch off the engine, stop the mechanism, remove the victim from under the car, a heavy object, etc.). Assistance should begin with the most significant that threatens life or health (in case of severe bleeding, apply a tourniquet, and then bandage the wound; if a closed fracture is suspected, apply a splint; with open fractures, first bandage the wound and then apply a splint; in case of burns, apply a dry bandage ; in case of frostbite, gently rub the affected area using soft or fluffy tissues). If spinal injury is suspected, transport the victim only in the supine position on a rigid base. 4.6. After providing first aid, the victim should be sent to the nearest medical facility. 5. Safety requirements at the end of work 5.1. Turn off equipment. Wait for it to come to a complete stop. Tidy up the workplace: remove tools, fixtures; clean the machine from dirt and dust; wipe and lubricate the rubbing parts of the machine; neatly fold the finished parts and the remaining material. 5.2. Cleaning of wood waste (sawdust, shavings, dust) from the surface of the equipment, as well as from overalls, is carried out with a brush, sweep or using vacuum cleaners. It is unacceptable to blow the machine and clothes with compressed air. 5.3. Rags used during work and when cleaning, put the rags in a special metal box with a closing lid and take it outside the workshop to a specially designated place. 5.4. Wash hands with warm water and soap. 5.5. Report all noticed shortcomings in the operation of the equipment to the shift worker or foreman. We recommend interesting articles Section Standard instructions for labor protection: ▪ Copier operator. Standard instruction on labor protection ▪ Maintenance of oxygen cylinders. Standard instruction on labor protection ▪ Discharge of liquefied gas into group tank installations. Standard instruction on labor protection See other articles Section Standard instructions for labor protection. Read and write useful comments on this article. Latest news of science and technology, new electronics: Artificial leather for touch emulation
15.04.2024 Petgugu Global cat litter
15.04.2024 The attractiveness of caring men
14.04.2024
Other interesting news: ▪ Robot dog Spot took part in military exercises ▪ Moderate noise is also harmful News feed of science and technology, new electronics
Interesting materials of the Free Technical Library: ▪ section of the site Protection of electrical equipment. Article selection ▪ article Show where crayfish hibernate. Popular expression ▪ article Which country has the right not to sign its postage stamps? Detailed answer ▪ article Head of the customs brokerage department. Job description
Leave your comment on this article: All languages of this page Home page | Library | Articles | Website map | Site Reviews www.diagram.com.ua |