OCCUPATIONAL SAFETY AND HEALTH
Instructions on labor protection when working on stationary and manual cutting electric machines. Full Document Occupational Safety and Health / Standard instructions for labor protection Safe Operation 1. General requirements for labor protection 1.1. Stationary cutting and manual electric machines are used for making cuts from fabric floorings in the mass production of clothing. Use of this equipment may result in cuts and electric shock. 1.2. Persons at least 18 years of age who have undergone special training and passed exams by the attestation commission of the enterprise, and who have been instructed at the workplace, are allowed to work on cutting machines. 1.3. Do not be distracted by extraneous work and do not allow yourself to be distracted by others. 1.4. In case of injury, contact the first-aid post and inform the administration of the workshop. 2. Labor protection requirements before starting work 2.1. Check the security of the guards and their fasteners. 2.2. Check the serviceability of the grounding and the condition of the insulation of the wires; 2.3. Check the condition of the working surface of the knife, the correct sharpening, the absence of side burrs; 2.4. Check the condition of the working surface of the knife, the correct sharpening, the absence of side burrs; 2.5. Remove unnecessary items from the table, do not clutter. 2.6. When working on manual cutters, tidy up and clean the guide groove of the knife, remove waste cloth and dirt near the rollers under the platform of the machine. 2.7. On manual cutters with a vertical knife, check and adjust the safety foot knives. 2.8. In disc cutters, check the correct rotation of the disc, according to the arrow on the machine body. 3. Labor protection requirements during work 3.1. It is forbidden to cut the flooring on electric cutting machines without fences (protectors against cutting hands). 3.2. Make sure that the band knife guards on the standard cutting machine and the knife guards on the manual cutting machine are lowered to the height of the fabric decks being cut. 3.3. Do not allow unauthorized persons to work on cutting machines. 3.4. Do not edit machines, knives on the move. 3.5. On stationary draw frames, check:
3.6. When cutting the flooring, follow the correct position of the hands in relation to the cutting edges of the knife, both during forward and reverse movement. The hand holding the deck must not cross the cutting lines. 3.7. Keep the knife sharp and sharpen it in a timely manner. Do not idle the car, turn it off during work breaks. 3.8. Make sure that for manual cutters, the terminal box fits snugly into the contacts of the motor one and that the machine is grounded. 3.9. If there is a smell of a burning motor, with a slight tingling from touching the machine body, with incomprehensible noises - stop work immediately, turn off the machine and call an electrician. 3.10. If the band knife breaks, turn off the machine, call an electrician. It is forbidden for fabric cutters to work on the equipment. It is forbidden to accelerate the stop of mechanisms to produce artificial braking of pulleys or gears after a power outage. 3.11. Spare band knives should be stored in protective places; and tie it into rolls and take it to the places where scrap metal is collected. 4. Labor protection requirements at the end of work 4.1. turn off the mechanisms, wait for a complete stop, perform technological maintenance measures (clean the machine, clean your workplace). 4.2. Stop the manual cutter only in the middle of the table, do not stop the machine on the floor or in the aisles. 4.3. This manual must be read by all who come into contact with the operation of this equipment. We recommend interesting articles Section Standard instructions for labor protection: ▪ Adjustment of automation and telemechanics. Standard instruction on labor protection ▪ A stamper at work on presses. Standard instruction on labor protection See other articles Section Standard instructions for labor protection. Read and write useful comments on this article. Latest news of science and technology, new electronics: Artificial leather for touch emulation
15.04.2024 Petgugu Global cat litter
15.04.2024 The attractiveness of caring men
14.04.2024
Other interesting news: ▪ Self-driving Volvo cars with all-round visibility ▪ Samsung SmartThings Wifi Mesh Network System News feed of science and technology, new electronics
Interesting materials of the Free Technical Library: ▪ section of the Electrician website. PUE. Article selection ▪ article Hallway wall. Tips for the home master ▪ article Can a tree communicate what it needs? Detailed answer
Leave your comment on this article: All languages of this page Home page | Library | Articles | Website map | Site Reviews www.diagram.com.ua |