Labor protection instructions for the installer

Free technical library

OCCUPATIONAL SAFETY AND HEALTH
Free library / Occupational Safety and Health / Standard instructions for labor protection

Labor protection instructions for the installer

Occupational Safety and Health

Occupational Safety and Health / Standard instructions for labor protection

Comments on the article

Safe Operation

1. General safety requirements

1.1. Persons under 18 years of age who have passed a medical examination are allowed to work independently as an installer, as well as:

induction training;
fire safety briefing;
initial briefing at the workplace;
training in safe working methods and techniques for at least a 10-hour program (for work that is subject to increased safety requirements - a 20-hour program);
instructing on electrical safety at the workplace and checking the assimilation of its content.

To perform the duties of an installer, persons who do not have medical contraindications for this profession, who have been trained and instructed in labor protection, can be accepted.

1.2. The installer must:

repeated briefing on labor safety at the workplace at least every three months;
unscheduled briefing: when changing the technological process or labor protection rules, replacing or modernizing production equipment, fixtures and tools, changing working conditions and organization, in case of violations of labor protection instructions, breaks in work for more than 60 calendar days (for work, to which are subject to increased security requirements - 30 calendar days);
dispensary medical examination according to the order of the Ministry of Health of the Russian Federation No. 90 dated 14.03.98

1.3. The installer must:

comply with the internal labor regulations established at the enterprise;
observe the rules for the design and safe operation of lifting mechanisms;
comply with the requirements of this manual, fire safety instructions, electrical safety instructions;
comply with safety requirements when using portable power tools; equipment operation;
use for its intended purpose and take care of the issued personal protective equipment.

1.4. The installer must:

be able to provide first (pre-medical) assistance to the victim in an accident;
know the location of first aid, primary fire extinguishing equipment, main and emergency exits, evacuation routes in case of an accident or fire;
perform only the assigned work and not transfer it to others without the permission of the foreman or head of the workshop;
during work, be attentive, not be distracted and not distract others, do not allow persons who are not related to work to the workplace;
keep the workplace clean and tidy.

1.5. The installer must know and follow the rules of personal hygiene. Eat, smoke, rest only in specially designated areas and places. Drink water only from specially designed installations.

1.6. If any malfunctions of equipment, fixtures, tools and other shortcomings or hazards are found in the workplace, immediately inform the foreman or head of the workshop. You can start work only with their permission after the elimination of all deficiencies.

1.7. If a fire is detected or in the event of a fire:

turn off the equipment;
inform the fire brigade and administration;
start extinguishing the fire with the primary fire extinguishing equipment available in the workshop in accordance with the fire safety instructions.

In case of a threat to life - leave the premises.

1.8. In case of an accident, provide the victim with first (pre-medical) aid, immediately report the incident to the foreman or head of the workshop, take measures to preserve the situation of the incident (equipment condition), if this does not create a danger to others.

1.9. For non-compliance with the safety requirements set forth in this manual, the installer is liable in accordance with applicable law.

1.10. In accordance with the "Model industry standards for the free issue of special clothing, special footwear and other personal protective equipment to workers and employees", a repairman is supposed to: a cotton suit - a wear period of 12 months and combined mittens - a wear period of 2 months. Permanently engaged outdoors in assembling and assembling in winter additionally: cotton jacket with insulating lining - wearing period is 30 months; cotton trousers - wearing period is 30 months.

The issued personal protective equipment should be stored in a dressing room in a closet, washed and repaired in the prescribed manner.

1.11. The main hazardous and harmful production factors under certain circumstances can be:

elements of production equipment;
details;
faulty working tools, fixtures and equipment;
electric current;
electrical equipment or wiring;
increased dustiness of the air;
increased noise level.

2. Safety requirements before starting work

2.1. Make sure that it is in good condition and put on overalls, remove your hair under a beret or cap.

2.2. Check your workplace, it should be evenly lit (no glare), not cluttered with foreign objects.

2.3. Check the serviceability of the tool and devices for installing doors:

electric portable tool;
the handle of a percussion instrument (hammer, etc.) must be oval in cross section and straight;
the surface of the hammer head must be convex, smooth, not beveled, without burrs;
the spindle of a hand tool with a pointed working end (files, screwdrivers, etc.) must be securely fixed in a smooth, smoothly cleaned handle, which, for greater strength, must be pulled together at both ends with metal bandage rings;
screwdrivers must be with non-curved rods, as the blade may slip off the head of the screw or screw and injure hands;
wrenches must correspond to the sizes of bolts and nuts, the jaws of wrenches must have strictly parallel jaws, the distance between which must correspond to the standard size indicated on the key;
socket and box wrenches must not move in the connected moving parts.

3. Safety requirements during work

3.1. Do only the work assigned by the master.

3.2. Be attentive in your work, do not distract yourself and do not distract others.

3.3. All items must be placed within the zone of maximum reach of the worker's hands, his hands must be free from performing supporting movements (these functions must be performed by devices).

3.4. When performing installation operations, observe the provisions of the technological map.

3.5. When working at height, it is necessary to securely fasten the mounting belt to reliable structures.

3.6. When lifting structures, the signaling should be organized in such a way that all signals to the workers employed on the guy line are given by only one worker, who is in charge of lifting.

3.7. Areas that are dangerous for the movement of people during installation must be fenced off and equipped with warning signals.

3.8. Slinging of products should be carried out only for mounting loops with slings equipped with carabiners, in accordance with the approved scheme for slinging loads.

3.9. When lifting the product, you must be at a distance of at least 1 m from it.

3.10. When lifting the product, moving it in a horizontal position, make it above the protruding parts by at least 0,5 m.

3.11. After installing the product, loosen the cables and make sure it is installed correctly.

3.12. It is forbidden to lay the mounted products on the platform decks.

3.13. Use only correct tools.

3.14. Work with a chisel to carry out in protective glasses.

3.15. When using a portable power tool (drill, grinder, etc.), when installing metal doors to a client, use special 42 V electrical wiring and observe the following safety requirements:

before switching on, make sure that the case is grounded and the wires are properly insulated;
check the tool at idle;
at a voltage of more than 42 V, use personal protective equipment (dielectric gloves, rugs);
turn off the tool when you stop working.

3.16. When using an electric drill, the objects to be drilled must be securely fastened. Do not touch the rotating cutting tool with your hands.

3.17. Do not remove shavings or sawdust by hand while the tool is running. Chips and sawdust must be removed after the power tool has completely stopped with special hooks or brushes.

3.18. Work with a drill no more than 2/3 of the working day. In accordance with sanitary standards, provide 1-15 minute breaks after each hour of work.

3.19. Wear rubber gloves and rubber mats when working with power tools to protect against electric shock.

3.20. For safety reasons, monitor the integrity of the insulation, prevent mechanical damage to the cable.

3.21. Switch off the power tool during work breaks. Do not connect the power tool to the mains without a special safety plug. This must be done by an electrician.

3.22. If the power tool suddenly stops, it must be turned off by the switch.

3.23. Persons working with power tools must not disassemble or repair the tool, cable, plug connections, or other parts themselves.

3.24. When removing or installing parts and assemblies on the machine, use the tools and devices provided for this type of work.

4. Safety requirements in emergency situations

4.1. In emergency situations, suspend work, leave the danger zone, and if necessary, remove workers nearby. If there is a danger of an accident, take measures to prevent it (stop the equipment or the corresponding mechanism, protect the danger zone). Report the incident to the supervisor.

4.2. In the event of a fire, immediately call the fire brigade by phone 01, remove people and, if possible, combustible substances to a safe place, start extinguishing the fire with the available primary fire extinguishing equipment. Report the fire to management.

4.3. Provide first aid to the injured in case of injury and call an ambulance, notify the work manager.

5. Safety requirements at the end of work

5.1. Tidy up your workspace. Remove tools and fixtures in the place provided for them.

5.2. Check the workplace after installing the door for fire safety.

5.3. Take off overalls, put them in a closet, wash your hands and face with soap, take a shower if possible, and do not use chemicals for washing.

We recommend interesting articles Section Standard instructions for labor protection:

▪ Sharpener. Standard instruction on labor protection

▪ Cutting machine work. Standard instruction on labor protection

▪ Work on the line-notebook unit. Standard instruction on labor protection

See other articles Section Standard instructions for labor protection.

Read and write useful comments on this article.

<< Back

Latest news of science and technology, new electronics:

Artificial leather for touch emulation 15.04.2024

In a modern technology world where distance is becoming increasingly commonplace, maintaining connection and a sense of closeness is important. Recent developments in artificial skin by German scientists from Saarland University represent a new era in virtual interactions. German researchers from Saarland University have developed ultra-thin films that can transmit the sensation of touch over a distance. This cutting-edge technology provides new opportunities for virtual communication, especially for those who find themselves far from their loved ones. The ultra-thin films developed by the researchers, just 50 micrometers thick, can be integrated into textiles and worn like a second skin. These films act as sensors that recognize tactile signals from mom or dad, and as actuators that transmit these movements to the baby. Parents' touch to the fabric activates sensors that react to pressure and deform the ultra-thin film. This ... >>

Petgugu Global cat litter 15.04.2024

Taking care of pets can often be a challenge, especially when it comes to keeping your home clean. A new interesting solution from the Petgugu Global startup has been presented, which will make life easier for cat owners and help them keep their home perfectly clean and tidy. Startup Petgugu Global has unveiled a unique cat toilet that can automatically flush feces, keeping your home clean and fresh. This innovative device is equipped with various smart sensors that monitor your pet's toilet activity and activate to automatically clean after use. The device connects to the sewer system and ensures efficient waste removal without the need for intervention from the owner. Additionally, the toilet has a large flushable storage capacity, making it ideal for multi-cat households. The Petgugu cat litter bowl is designed for use with water-soluble litters and offers a range of additional ... >>

The attractiveness of caring men 14.04.2024

The stereotype that women prefer "bad boys" has long been widespread. However, recent research conducted by British scientists from Monash University offers a new perspective on this issue. They looked at how women responded to men's emotional responsibility and willingness to help others. The study's findings could change our understanding of what makes men attractive to women. A study conducted by scientists from Monash University leads to new findings about men's attractiveness to women. In the experiment, women were shown photographs of men with brief stories about their behavior in various situations, including their reaction to an encounter with a homeless person. Some of the men ignored the homeless man, while others helped him, such as buying him food. A study found that men who showed empathy and kindness were more attractive to women compared to men who showed empathy and kindness. ... >>

Random news from the Archive

IGBT modules with a total lead inductance of 15 nH 30.11.2009

SEMIKRON has introduced the latest generation of low inductance 1200 V SEMITRANS IGBT modules designed for use in 20...300 kW converters. Now these modules will be equipped with V-IGBT (Fuji) chips, similar in their characteristics to Trench 4 crystals.

The new IGBTs feature smoother switching characteristics and lower dynamic losses to improve conversion efficiency. V-IGBT crystals will be installed in three module sizes in three different configurations, designed for use in eight power ranges. The operating current range of the power switches is 150...600 A. The total inductance of SEMITRANS 3 and 4 outputs is reduced to 15 nH.

With a typical IGBT switching speed of 5000 A/µs, the amplitude of switching surges is only 75 V. For power switches of the same class available on the market, this value is in the range of 90...125 V. The new modules will be produced in basic configurations, necessary for the design of industrial converters: single keys, half-bridges and choppers. The insulation voltage of the components of the new SEMITRANS family is 4000 V, they are equipped with 4 types of IGBT crystals: IGBT2, IGBT2 fast, IGBT3, IGBT4.

SEMITRANS modules have 3 operating voltage classes: 600 V, 1200 V and 1700 V, they are produced in 3 standard sizes of housings of 34 mm and 62 mm standards. Also available are 6 key SEMITRANS 6 according to the 3-phase inverter scheme, SEMITRANS 5 for building a 3-level inverter with an integrated current shunt. A SEMITRANS 9 with an isolation voltage of 9 kV for railway applications is under development.

Other interesting news:

▪ Microsoft servers will be equipped with their own processors

▪ Robots instead of astronauts

▪ Birds also have a cerebral cortex

▪ EVGA GQ Series 80Plus Gold Power Supplies

▪ Instant dimming for the welder

News feed of science and technology, new electronics

Interesting materials of the Free Technical Library:

▪ section of the Antenna website. Article selection

▪ photosynthesis article. History and essence of scientific discovery

▪ article How did the god of war Ares differ from the goddess of war Athena? Detailed answer

▪ article Operation of vacuum pumps. Standard instruction on labor protection

▪ article USB voltage recorder with oscilloscope, spectrum analyzer and frequency response meter functions. Encyclopedia of radio electronics and electrical engineering

▪ article Does water have skin? Physical experiment. physical experiment

Leave your comment on this article:

All languages of this page

Home page | Library | Articles | Website map | Site Reviews