Instruction on labor protection for the driver of a road combined KDM car

Free technical library

OCCUPATIONAL SAFETY AND HEALTH
Free library / Occupational Safety and Health / Standard instructions for labor protection

Instruction on labor protection for the driver of a road combined KDM car

Occupational Safety and Health

Occupational Safety and Health / Standard instructions for labor protection

Comments on the article

Safe Operation

1. General safety requirements

1.1. Individuals who have passed:

induction training;
fire safety briefing;
initial briefing at the workplace;
electrical safety training in the workplace.

Persons who have a certificate for the right to drive this category of transport, who do not have medical contraindications for this profession, and who have reached the age of 18, are allowed to perform the duties of a driver of the KDM.

1.2. The driver of the KDM must pass:

repeated briefing on labor safety at the workplace at least every three months;
unscheduled briefing: when changing the technological process or labor protection rules, replacing or upgrading a truck, fixtures and tools, changing working conditions and organization, in case of violations of labor protection instructions, breaks in work for more than 60 calendar days (for work, to which are subject to increased security requirements - 30 calendar days);
dispensary medical examination according to the order of the Ministry of Health of the Russian Federation No. 90 dated March 14.03.96, XNUMX.

1.3. The driver of the KDM is obliged:

comply with the internal labor regulations established at the enterprise;
comply with the requirements of this manual, fire safety instructions, electrical safety instructions;
comply with the requirements for the operation of the car;
use for its intended purpose and take care of the issued personal protective equipment.

1.4. When registering a driver for work, a certain KDM car must be assigned to him by order of the enterprise.

1.5. After being hired, the driver is obliged to accept the vehicle according to the act and perform only the work that is assigned by the administration of the transport department.

1.6. The driver of the KDM must:

be able to provide first (pre-medical) assistance to the victim in an accident;
have on the car a first-aid kit for first aid, primary fire extinguishing equipment;
perform only assigned work and not transfer it to others without the permission of the head of the AHO;
during work, be attentive, not be distracted and not distract others, do not allow persons who are not related to work to the workplace;
keep the workplace clean and tidy.

1.7. The driver must know and follow the rules of personal hygiene. Eat, smoke, rest only in specially designated areas and places. Drink water only from specially designed installations.

1.8. Stop the vehicle immediately if you detect malfunctions of the vehicle, fixtures, tools and other shortcomings or hazards in the workplace. Only after eliminating the noticed shortcomings, continue working on the car.

1.9. If a fire is detected or in the event of a fire:

stop the car, turn off the ignition, turn off the valves of the gas pipeline and fuel and lubricants;
start extinguishing the fire with the available primary fire extinguishing equipment in accordance with the fire safety instructions. In case of a threat to life - leave the premises.

1.10. In case of an accident, provide the victim with first (pre-medical) aid, immediately report the incident to the foreman or head of the shop, take measures to preserve the situation of the incident (accident), if this does not create a danger to others.

1.11. For non-compliance with the safety requirements set forth in this manual, the worker is liable in accordance with applicable law.

1.12. In accordance with the "Typical industry norms for the free issue of special clothing, special footwear and other personal protective equipment to workers and employees", the driver of the KDM car must be provided with cotton overalls (wearing period 12 months), combined two-fingered mittens (wearing period 6 months)

1.13. The main dangerous and harmful production factors are:

moving and rotating parts and components of the car;
hot surfaces of the engine, cooling system, muffler, etc.
exhaust gases resulting from the combustion of fuels and lubricants;
collision with another vehicle or collision with people;
falling cargo during loading and unloading operations and its transportation.

2. Safety requirements before starting work

2.1. Make sure that it is in good working order and put on serviceable special clothes, fastening it with all buttons, put your hair under a headdress.

2.2. Visual inspection to make sure the car is in full working order and check:

the technical condition of the vehicle and trailer, paying special attention to the presence of a protective screen, serviceability of tires, auger spreader, brake system, steering, road train coupling devices, lighting and signaling devices, windshield wipers, correct installation of the rear-view mirror, cleanliness and visibility of license plates and duplicating their inscriptions;
no leakage of fuel, oil and water, and for gas-balloon vehicles for tightness of gas equipment and lines;
air pressure in tires in accordance with the norms;
the availability of serviceable tools and fixtures;
filling the car with fuel, oil, water, brake fluid and electrolyte level in the battery.

2.3. To start a cold engine, use the starting handle with the gear lever in neutral position. It is not allowed to grasp the handle or use any levers acting on it.

2.4. After starting or warming up the engine, it is necessary to check on the go the operation of the steering and brakes, the operation of the "STOP" signal, turns, lighting, as well as the sound signal.

2.5. In case of detection of malfunctions, do not go to the line until they are completely eliminated and inform the administration of the motor transport department about this.

2.6. Refuel the car with fuel after stopping the engine.

2.7. When running a car on leaded gasoline, observe the following rules:

operations for the acceptance, refueling of the car and pumping of leaded gasoline to be carried out mechanized, being on the windward side of the car;
purge the fuel system with a pump;
if leaded gasoline gets on your hands, wash them with kerosene, and then with warm water and soap;
If leaded petrol comes into contact with eyes, seek immediate medical attention.

2.8. Open the radiator cap after the engine has cooled down, protect your hands and face from burns.

2.9. In order to increase safety, the connection of the vehicle with the trailer should be by means of a rigid drawbar fixed to the frame of the vehicle with a king pin with a nut. Connect the king pin to the drawbar so that it can turn freely; the axis of the drawbar of the trailer in its horizontal position must be at the same level with the pivot.

3. Safety requirement during operation

3.1. Before starting to move from the place of stop (parking) or leaving the garage, make sure that it is safe for workers and other unauthorized persons and give a warning signal.

3.2. Be alert and careful when reversing. In case of insufficient visibility or visibility, you should take the help of another person.

3.3. The speed of movement should be selected taking into account road conditions, visibility and visibility, the intensity and nature of the movement of vehicles and pedestrians, the characteristics and condition of the vehicle and the cargo being transported.

3.4. Follow traffic safety requirements and instructions of traffic controllers in accordance with the "Rules of the Road".

3.5. Filling the tank with water should be done in a place specially adapted for this, on a horizontal platform, in natural light. If necessary, refueling can be done at night with sufficient artificial lighting.

3.6. When refueling with water, the driver must leave the cab, leaving the car on the handbrake.

3.7. The pump must be switched on at a speed of no more than 30 km/h.

3.8. Choose the speed of movement based on road conditions, visibility and visibility, the intensity and nature of the movement of vehicles and pedestrians.

3.9. It is allowed to leave the car only after taking measures that exclude the possibility of its movement during the absence of the driver.

3.10. When repairing a car on the line, take precautions: pull over to the side of the road, turn on the rear light in case of poor visibility, stop the car using the parking brake system, engage first gear, put stops under the wheels. When working on the side of the road, stay under the vehicle on the opposite side of the roadway. Do not allow persons who do not have the right to repair the car (loaders, accompanying passengers, etc.).

3.11. The driver of the KDM is not allowed to:

drive a car while intoxicated;
or under the influence of drugs;
leave for a flight in a sick condition or with such a degree of fatigue that may affect traffic safety;
when the car is parked, sleep and rest in the cab with the engine running or start the engine to heat the cab; transfer control of the car to unauthorized persons;
carry out maintenance and repair of the vehicle during loading and unloading;
to transport passengers in a car not equipped for the transportation of people, as well as travel in the cabin of people in excess of the established norm for this type of car;
carry out towing of the car in order to start the engine;
heat the engine with an open flame, as well as when identifying and eliminating malfunctions of mechanisms;
wipe the engine with a rag soaked in gasoline and smoke in the immediate vicinity of the engine power system and fuel tanks.

3.13. When placing the car at a service station that does not have a forced movement, or repair, tighten the parking brake lever and engage first gear. Hang a sign on the steering wheel "Do not start the engine! People are working!"

3.14. When repairing a car, keep the workplace clean and not clutter up with foreign objects. Drain oil and water only into a special container.

3.15. When performing repair work on a dump truck with a raised body, first strengthen the body with a bar.

3.16. Lift the car with a jack without distortions (the jack must stand vertically, rest on the ground with the entire plane of the sole, the head of the jack must rest with the entire plane against the axis or in a specially fixed place, if the ground is soft, put a board under the jack, put shoes under the rest of the wheels).

3.17. To remove and install heavy components and assemblies, use lifting and transport vehicles, without exceeding the maximum carrying capacity of these vehicles.

3.18. For disassembly and assembly work, use only serviceable fixtures and tools. Moisten nuts that are difficult to unscrew with kerosene, and then unscrew them with a wrench.

3.19. Check the alignment of the hole of the spring eyelet and the earring only with the help of a beard.

3.20. Tighten the fan belt, check the fastening of the water pump and tighten the oil seals only after the engine has completely stopped.

3.21. Work related to the replacement and rearrangement of tires, springs should be performed only after the car is installed on the trestle.

3.22. Remove the tire from the wheel disk using a puller, inflate the tires in the safety device. When inflating tires on the line, lay the wheel with the key ring to the ground.

4. Safety requirements in emergency situations

4.1. The driver involved in a traffic accident that caused an accident (hitting people or a collision with another vehicle) must immediately inform the traffic police, the master or the dispatcher; provide the victim with first (pre-medical) aid, take measures to preserve the situation of the incident (accident) until the arrival of the traffic police, if this does not create a danger to others.

4.2. You can take a faulty car in tow with the help of special devices after the permission of the traffic police inspector.

5. Safety requirements at the end of work

5.1. After returning from the line, together with the mechanic of the transport department, check the car. If necessary, draw up an application for current repairs with a list of faults to be eliminated.

5.2. Clean the car of dirt and dust, put them in the designated place, make sure that there is no possibility of fire and tighten the parking brake lever.

5.3. Hand over the waybill to the dispatcher or responsible person.

5.4. Remove and put special clothes in the closet, wash hands and face with soap and water, take a shower. Do not use chemicals for washing.

We recommend interesting articles Section Standard instructions for labor protection:

▪ A worker for packing oil products into barrels and small containers at oil product supply enterprises. Standard instruction on labor protection

▪ Preparation of felling areas for felling. Standard instruction on labor protection

▪ Shipbuilder-repairer. Standard instruction on labor protection

See other articles Section Standard instructions for labor protection.

Read and write useful comments on this article.

<< Back

Latest news of science and technology, new electronics:

Artificial leather for touch emulation 15.04.2024

In a modern technology world where distance is becoming increasingly commonplace, maintaining connection and a sense of closeness is important. Recent developments in artificial skin by German scientists from Saarland University represent a new era in virtual interactions. German researchers from Saarland University have developed ultra-thin films that can transmit the sensation of touch over a distance. This cutting-edge technology provides new opportunities for virtual communication, especially for those who find themselves far from their loved ones. The ultra-thin films developed by the researchers, just 50 micrometers thick, can be integrated into textiles and worn like a second skin. These films act as sensors that recognize tactile signals from mom or dad, and as actuators that transmit these movements to the baby. Parents' touch to the fabric activates sensors that react to pressure and deform the ultra-thin film. This ... >>

Petgugu Global cat litter 15.04.2024

Taking care of pets can often be a challenge, especially when it comes to keeping your home clean. A new interesting solution from the Petgugu Global startup has been presented, which will make life easier for cat owners and help them keep their home perfectly clean and tidy. Startup Petgugu Global has unveiled a unique cat toilet that can automatically flush feces, keeping your home clean and fresh. This innovative device is equipped with various smart sensors that monitor your pet's toilet activity and activate to automatically clean after use. The device connects to the sewer system and ensures efficient waste removal without the need for intervention from the owner. Additionally, the toilet has a large flushable storage capacity, making it ideal for multi-cat households. The Petgugu cat litter bowl is designed for use with water-soluble litters and offers a range of additional ... >>

The attractiveness of caring men 14.04.2024

The stereotype that women prefer "bad boys" has long been widespread. However, recent research conducted by British scientists from Monash University offers a new perspective on this issue. They looked at how women responded to men's emotional responsibility and willingness to help others. The study's findings could change our understanding of what makes men attractive to women. A study conducted by scientists from Monash University leads to new findings about men's attractiveness to women. In the experiment, women were shown photographs of men with brief stories about their behavior in various situations, including their reaction to an encounter with a homeless person. Some of the men ignored the homeless man, while others helped him, such as buying him food. A study found that men who showed empathy and kindness were more attractive to women compared to men who showed empathy and kindness. ... >>

Random news from the Archive

Microsoft will release a revolutionary smartphone 27.11.2016

Microsoft CEO Satya Nadella has announced that the company will release a groundbreaking mobile device in 2017, the Surface Phone.

The head of Microsoft told some technological details in an interview with the national Australian financial and economic newspaper Australian Financial Review. "We continue to remain in the mobile market, but we are not equal to its leaders. However, we can definitely create the optimal mobile device. Therefore, we stopped making gadgets from the category "and I am the same", and focused on devices for the specific needs of a client who needs a specific set of possibilities," Nadella said.

As an example of a device that has changed the mobile market, Nadella named the HP Elite x3 smartphone, HP's flagship model. Its peculiarity is that it can be used as a PC by connecting a mouse and keyboard to it.

We can talk about a device implemented taking into account two main trends that the company is now actively developing: open source software and cloud services. It is possible that the "revolutionary device" will be connected to such Microsoft applications as a manager with the functions of an Outlook email client or OneNote notepad organizer. That is, the programs will be pre-installed on the new smartphone, as it is now happening under the existing agreement with some Asus and Samsung Android devices, on which Microsoft Office is installed at the factory.

Other interesting news:

▪ Portable Vaccine Patch Printer

▪ Texts are typed only by eye movement

▪ LG 6-core LCD TVs

▪ The car will understand that the driver is talking on a mobile phone

▪ 800V MOSFET P7 CoolMOS by Infineon

News feed of science and technology, new electronics

Interesting materials of the Free Technical Library:

▪ section of the site Microphones, radio microphones. Article selection

▪ article Rules of safe behavior on public transport. Basics of safe life

▪ article What is the difference between phrases called spoonerisms? Detailed answer

▪ Article Blood pressure and its measurement. Health care

▪ article Shaft speed controller of a microelectric motor. Encyclopedia of radio electronics and electrical engineering

▪ article Two voltages from one winding of the transformer. Encyclopedia of radio electronics and electrical engineering

Leave your comment on this article:

All languages of this page

Home page | Library | Articles | Website map | Site Reviews