Instructions for labor protection when working on proofing machines

Free technical library

OCCUPATIONAL SAFETY AND HEALTH
Free library / Occupational Safety and Health / Standard instructions for labor protection

Instructions on labor protection when working on test printing machines. Full Document

Occupational Safety and Health

Occupational Safety and Health / Standard instructions for labor protection

Comments on the article

Safe Operation

1. General requirements for labor protection

1.1. Persons who have passed a medical examination and have no contraindications to work in this profession (specialty), introductory briefing and briefing at the workplace are allowed to work. Workers are allowed to work independently after an internship, verification of theoretical knowledge and acquired skills in safe ways of working. In the future, at the workplace, briefings on labor protection are held at least once every 3 months.

1.2. When transferring to a new job, from temporary to permanent, from one operation to another with a change in the technological process or equipment, employees must be instructed in labor protection at the workplace.

1.3. Conducting all types of briefings must be recorded in the Briefing Log with the obligatory signatures of the person who received and conducted the briefing.

1.4. Each employee is obliged to comply with the requirements of this instruction, labor and production discipline, work and rest regime, all requirements for labor protection, safe work performance, industrial sanitation, fire safety, electrical safety.

1.5. Smoking is allowed only in specially designated areas. The use of alcoholic beverages at work, as well as going to work in a state of alcoholic or drug intoxication, is prohibited.

1.6. When performing work, it is necessary to be attentive, not to be distracted by extraneous affairs and conversations, and not to distract others from work. It is forbidden to sit down and lean on random objects and fences.

1.7. It is forbidden to approach operating machines, installations, machines on which other workers work, and distract them with extraneous conversations, turn on or off (except in emergency cases) equipment, transport and lifting mechanisms, work on which is not assigned, go beyond the fences of hazardous areas, in zones of technological passages.

1.8. The employer is obliged to provide workers with overalls, safety shoes, as well as personal protective equipment in accordance with the work they perform and in accordance with applicable standards. It is forbidden to work without overalls, safety shoes and other personal protective equipment laid down in accordance with the standards.

1.9. Each employee needs:

know the place of storage of the workshop first-aid kit;
be able to provide first aid for work-related injuries.

1.10. It is allowed to store and eat food only in established and equipped places.

1.11. It is forbidden to be in production premises in outerwear, undress or hang clothes, hats, bags on equipment.

1.12. Do not clutter up passages, driveways, workplaces, approaches to shields with fire fighting equipment, fire hydrants and a general switch.

1.13. Spilled cleaners, lubricants, water, etc. on the floor. wipe off immediately.

1.14. Cleaning materials impregnated with oil, paint, solvent, put in tightly closed metal boxes. Do not scatter these materials, at the end of the shift they should be removed from the premises.

1.15. Store fuels, lubricants and flammable liquids only in a tightly closed metal container (box) or cabinet in an amount not exceeding the replacement rate. Joint storage of acids and flammable and combustible liquids (gasoline, toluene, alcohol, kerosene, white spirit, etc.) is prohibited. Store chemicals in quantities not exceeding the established norms, in a tightly closed container with an inscription on the contents.

1.16. It is forbidden to repair equipment, fix electrical equipment and the electrical network to personnel who do not have access to these works, work near unshielded current-carrying parts, touch electrical wires, general lighting fittings, open doors of electrical cabinets, fencing of knife switches, switchboards and control panels.

1.17. Do not use lubricants for washing hands.

1.18. It is forbidden to be in the production room after the end of work.

1.19. The employee is responsible in accordance with applicable law for compliance with the requirements of instructions, industrial injuries and accidents that occurred through his fault.

1.20. The control of the implementation of this instruction is assigned to the head of the department.

2. Safety requirements before starting work

2.1. Put on overalls, fasten it with all buttons. Check the availability and serviceability of personal protective equipment.

2.2. Visually check the workplace and equipment, the serviceability of the protective earthing system, the presence and strength of fastening of fences, safety devices, interlocks, the operation of ventilation installations, the serviceability of water taps and water drains.

2.3. Report any deficiencies to the head of the department. Do not start work until the problem is fixed.

3. Safety requirements during work

3.1. Metal form frames should have a smooth surface, without burrs, cracks and cracks.

3.2. Work on the pneumatic tensioning device and pneumatic copy frame is only allowed if a sealed and serviceable pressure gauge and safety valve are available.

3.3. When working with the adhesive composition "TK", chromium salts and other chemicals and solutions, use protective equipment (rubber gloves). Wash off chemical reagents or solutions that have come into contact with the hands and body with a plentiful stream of water.

4. Safety requirements in emergency situations

4.1. In case of fire, immediately turn off the equipment, turn off the power supply, with the exception of the lighting network. Report the fire to everyone working in the room and proceed to extinguish the fire with the available fire extinguishing equipment.

4.2. If voltage (sensation of current) is detected on the metal parts of the equipment, the ventilation system is turned off, noise and vibration appear, the power is turned off, turn off the equipment immediately, report the malfunction to the foreman and do not start work without his instructions.

4.3. In case of contact with the skin:

alkalis (solutions) use 2 - 3% solution of acetic acid;
acids (solutions) use a 5% solution of baking soda.

4.4. In case of contact with the mucous membrane:

alkalis (solutions) use 1 - 2% solution of acetic acid;
acids (solutions) use a 2 - 3% solution of baking soda.

4.5. After neutralization, the affected areas should be washed with plenty of water.

4.6. If a direct stream of light gets into the eyes (from mercury and other lamps), rinse them with infusion of tea or water and immediately consult a doctor.

4.7. In case of injury, first of all, release the victim from the traumatic factor, notify the work manager, call for medical assistance, provide first aid to the victim and maintain a traumatic situation until the causes of the incident are investigated.

5. Safety requirements at the end of work

5.1. Turn off equipment and lighting installations, remove tools and fixtures to the designated places, tidy up the workplace.

5.2. Report malfunctions to the head of the workshop, section.

5.3. Check if heaters, lighting, ventilation, water, gas are turned off.

5.4. Remove personal protective equipment and overalls, put them in a closet.

5.5. Wash hands thoroughly and wash with warm water and soap.

We recommend interesting articles Section Standard instructions for labor protection:

▪ Radio measuring works. Standard instruction on labor protection

▪ Bread cutter. Standard instruction on labor protection

▪ Truck driver. Standard instruction on labor protection

See other articles Section Standard instructions for labor protection.

Read and write useful comments on this article.

<< Back

Latest news of science and technology, new electronics:

Artificial leather for touch emulation 15.04.2024

In a modern technology world where distance is becoming increasingly commonplace, maintaining connection and a sense of closeness is important. Recent developments in artificial skin by German scientists from Saarland University represent a new era in virtual interactions. German researchers from Saarland University have developed ultra-thin films that can transmit the sensation of touch over a distance. This cutting-edge technology provides new opportunities for virtual communication, especially for those who find themselves far from their loved ones. The ultra-thin films developed by the researchers, just 50 micrometers thick, can be integrated into textiles and worn like a second skin. These films act as sensors that recognize tactile signals from mom or dad, and as actuators that transmit these movements to the baby. Parents' touch to the fabric activates sensors that react to pressure and deform the ultra-thin film. This ... >>

Petgugu Global cat litter 15.04.2024

Taking care of pets can often be a challenge, especially when it comes to keeping your home clean. A new interesting solution from the Petgugu Global startup has been presented, which will make life easier for cat owners and help them keep their home perfectly clean and tidy. Startup Petgugu Global has unveiled a unique cat toilet that can automatically flush feces, keeping your home clean and fresh. This innovative device is equipped with various smart sensors that monitor your pet's toilet activity and activate to automatically clean after use. The device connects to the sewer system and ensures efficient waste removal without the need for intervention from the owner. Additionally, the toilet has a large flushable storage capacity, making it ideal for multi-cat households. The Petgugu cat litter bowl is designed for use with water-soluble litters and offers a range of additional ... >>

The attractiveness of caring men 14.04.2024

The stereotype that women prefer "bad boys" has long been widespread. However, recent research conducted by British scientists from Monash University offers a new perspective on this issue. They looked at how women responded to men's emotional responsibility and willingness to help others. The study's findings could change our understanding of what makes men attractive to women. A study conducted by scientists from Monash University leads to new findings about men's attractiveness to women. In the experiment, women were shown photographs of men with brief stories about their behavior in various situations, including their reaction to an encounter with a homeless person. Some of the men ignored the homeless man, while others helped him, such as buying him food. A study found that men who showed empathy and kindness were more attractive to women compared to men who showed empathy and kindness. ... >>

Random news from the Archive

Airplane powered by steam jet 24.06.2002

A model aircraft with a steam jet engine has been manufactured and successfully tested at the Tokyo Institute of Technology. A small paper airplane is propelled by jets of water vapor produced by an infrared solid-state laser.

The project manager, Professor T. Lbe, believes that in 30 years, stratospheric supersonic liners will be built on this principle.

Other interesting news:

▪ New microcontroller from Maxim

▪ Wheat grown tolerant of salty soil

▪ New technology of optical signal transmission over long distances

▪ diamond plow

▪ Scientists combine brain cells and a silicon chip

News feed of science and technology, new electronics

Interesting materials of the Free Technical Library:

▪ site section Color and music installations. Selection of articles

▪ Article Teaching, learning. Popular expression

▪ article How Dalmatians (a breed of dog) helped firefighters in the days of horse traction? Detailed answer

▪ Jute article. Legends, cultivation, methods of application

▪ article Overheating indicator. Encyclopedia of radio electronics and electrical engineering

▪ Hi-Fi article and volume control. Encyclopedia of radio electronics and electrical engineering

Leave your comment on this article:

All languages of this page

Home page | Library | Articles | Website map | Site Reviews