Instructions for labor protection when servicing bowling equipment

Free technical library

OCCUPATIONAL SAFETY AND HEALTH
Free library / Occupational Safety and Health / Standard instructions for labor protection

Instructions for labor protection when servicing bowling equipment. Full Document

Occupational Safety and Health

Occupational Safety and Health / Standard instructions for labor protection

Comments on the article

Safe Operation

Working Safely When Servicing Pinsetters GS Series

As with any other machinery, as with the Pinsetter (hereinafter referred to as the GS Pinsetter), there is an element of risk if the appropriate safety requirements are not observed. Under normal circumstances, knowledge of how the pinsetter works and basic safety precautions will prevent the possibility of injury to personnel operating the pinsetter.

1. Only specially trained mechanics may work with pinsetters.

2. Only special tools should be used for work. Before turning on the machine, remove all tools from it.

3. When working with the pinsetter, special work clothes should be worn. Do not wear ties or other loose clothing that could get caught in the car. Shoes must have a safe non-slip sole.

4. Avoid using toxic and poisonous cleaners.

5. When working, always have a fire extinguisher at hand that is in working order. Rags for greasing should be stored in a fireproof container.

6. Care must be taken when positioning the mechanic in front of the machine, as when the gassetter is on, movement of your hand or foot may trigger a photocell, after which the machine will begin the work cycle.

7. When working with one GS pinsetter, turn off the toggle switch on the High Voltage box or the rear toggle switch located on the pin lift, move the stop / run toggle switch on the Low Voltage box to the stop position (stop). If more than one mechanic is working on the machine, both switches must be turned off to avoid having the first mechanic turn the machine on before the other has finished working on it.

8. When working with both machines of the same pair of lanes (for example, with an electronic control unit or a ball accelerator), turn off the power at the Common Box and disconnect the power cable from it, turn off the power at the Combined High Voltage Box and disconnect the power cable from the High Voltage Box.

9. When using a pinsetter or ball accelerator, the pin shield must always be in the down position.

10. When maintenance is required from below the setting table, use a jack or other auxiliary equipment to support the center of the table.

Safe work with the counter

As with any machine, failure to follow safety guidelines when handling a Frameworx type scoring meter involves risk. Common sense knowledge of the pinsetting machine and scoring machine and basic safety precautions will help prevent injury to personnel working with these machines.

1. Only properly trained persons should operate the scoring counter.

2. Always disconnect mains power before dismantling any scoring units or other equipment to avoid personal injury.

3. It is not allowed to bypass or bypass any safety interlocks provided in the equipment.

4. All adjustments to the equipment should always be made with one hand. The other hand should be behind the back to avoid electric shock or electric shock.

5. Before removing or working on printed circuit boards and electronic modules, discharge any static charge accumulated on the body by touching the metal chassis of nearby equipment.

6. Before applying mains voltage to any piece of equipment, make sure that all bystanders are at a sufficient distance.

7. Do not spray printed circuit boards with aerosols. If cleaning is necessary, remove the module, moisten a cloth and wipe the board and its connections with this cloth.

8. Avoid using metal adjustment tools.

9. Remove all loose jewelry and large rings before working on the equipment.

10. Always use tools designed for this type of work. All tools must be removed before turning on the equipment.

11. Wear appropriate clothing and shoes with safe non-slip soles when operating the pin-setting machines. The machine may pick up a tie or loose clothing.

12. The use of toxic or poisonous cleaning agents should be avoided.

13. A fire extinguisher must be placed near the machine and must be kept in working condition. Store oily rags in a fireproof container.

14. Be careful when standing in front of the pin-setting machine. If it is turned on, your foot or hand may accidentally turn on the machine if it is equipped with an autostart system.

15. Always lower the scraper or ejector board when operating the pin-setting machine.

16. After maintenance of the equipment, all guards must be returned to their place.

We recommend interesting articles Section Standard instructions for labor protection:

▪ Safety diver. Standard instruction on labor protection

▪ Single bucket excavator operator. Standard instruction on labor protection

▪ Locksmith for the manufacture of components and parts of sanitary systems. Standard instruction on labor protection

See other articles Section Standard instructions for labor protection.

Read and write useful comments on this article.

<< Back

Latest news of science and technology, new electronics:

Artificial leather for touch emulation 15.04.2024

In a modern technology world where distance is becoming increasingly commonplace, maintaining connection and a sense of closeness is important. Recent developments in artificial skin by German scientists from Saarland University represent a new era in virtual interactions. German researchers from Saarland University have developed ultra-thin films that can transmit the sensation of touch over a distance. This cutting-edge technology provides new opportunities for virtual communication, especially for those who find themselves far from their loved ones. The ultra-thin films developed by the researchers, just 50 micrometers thick, can be integrated into textiles and worn like a second skin. These films act as sensors that recognize tactile signals from mom or dad, and as actuators that transmit these movements to the baby. Parents' touch to the fabric activates sensors that react to pressure and deform the ultra-thin film. This ... >>

Petgugu Global cat litter 15.04.2024

Taking care of pets can often be a challenge, especially when it comes to keeping your home clean. A new interesting solution from the Petgugu Global startup has been presented, which will make life easier for cat owners and help them keep their home perfectly clean and tidy. Startup Petgugu Global has unveiled a unique cat toilet that can automatically flush feces, keeping your home clean and fresh. This innovative device is equipped with various smart sensors that monitor your pet's toilet activity and activate to automatically clean after use. The device connects to the sewer system and ensures efficient waste removal without the need for intervention from the owner. Additionally, the toilet has a large flushable storage capacity, making it ideal for multi-cat households. The Petgugu cat litter bowl is designed for use with water-soluble litters and offers a range of additional ... >>

The attractiveness of caring men 14.04.2024

The stereotype that women prefer "bad boys" has long been widespread. However, recent research conducted by British scientists from Monash University offers a new perspective on this issue. They looked at how women responded to men's emotional responsibility and willingness to help others. The study's findings could change our understanding of what makes men attractive to women. A study conducted by scientists from Monash University leads to new findings about men's attractiveness to women. In the experiment, women were shown photographs of men with brief stories about their behavior in various situations, including their reaction to an encounter with a homeless person. Some of the men ignored the homeless man, while others helped him, such as buying him food. A study found that men who showed empathy and kindness were more attractive to women compared to men who showed empathy and kindness. ... >>

Random news from the Archive

VHS continues to lose ground 19.06.2003

For a long time, the DVD format could not seriously shake the position occupied by VHS standard media in the consumer video sector. It wasn't until the prices of DVD drives, and then consumer players, dropped sharply that the position of the VHS standard in the market began to deteriorate steadily.

Digital media with better picture and sound quality now costs not much more than a regular video cassette, so more and more people are choosing to buy DVD-ready equipment.

A recently California-based organization called the Video Software Dealers Association celebrated the first ever increase in DVD rentals over VHS rentals. During the week in the United States, video rental customers checked out 28,2 million DVDs and only 27,3 million VHS tapes.

If earlier it was noted that the number of sold DVD players exceeded the number of sold VCRs, now it is already obvious that the demand for the "new" format predominates among the media as well. The moment when VHS will take its well-deserved place in history next to vinyl records is inexorably approaching.

Other interesting news:

▪ Microchip MIC28514/5 buck converter

▪ Microelectrodes help to find out the word made by a person

▪ Qualcomm Snapdragon 602A Processor for Automotive Media Centers

▪ MOSFET driver type MAX5078

▪ New type of atomically thin carbon material discovered

News feed of science and technology, new electronics

Interesting materials of the Free Technical Library:

▪ section of the site Radio - for beginners. Article selection

▪ article Basic principles and legal framework for the protection of the population from emergencies. Fundamentals of safe life

▪ article How do we read? Detailed answer

▪ article Diver working. Standard instruction on labor protection

▪ article Electrician's tool. Directory

▪ article Invisible paints. Chemical experience

Leave your comment on this article:

All languages of this page

Home page | Library | Articles | Website map | Site Reviews