Instruction on labor protection for a fitter

Free technical library

OCCUPATIONAL SAFETY AND HEALTH
Free library / Occupational Safety and Health / Standard instructions for labor protection

Instructions on labor protection for a fitter. Full document

Occupational Safety and Health

Occupational Safety and Health / Standard instructions for labor protection

Comments on the article

Safe Operation

1. General safety requirements

1.1. Persons who have passed:

medical commission upon admission to work;
industrial training in the profession, knowledge testing in the qualification commission;
safety briefing;
pass a safety briefing for group I in electrical safety.

1.2. Only work that is the responsibility of a fitter or entrusted by the management of the enterprise should be performed, indicating the place and provided that the worker is well aware of the safety rules for performing work.

1.3. During work, as well as being on the territory of the production premises, be attentive, not be distracted and not distract the attention of others.

1.4. Do not touch electrical equipment, electrical devices, wires, wherever they are.

1.5. During operation, use a portable power tool with a voltage of 12 V.

1.6. The greatest danger during tight work is electric shock, as well as injury during cleaning work with fragments of abrasive and metal burrs.

1.7. The management of the enterprise is obliged to provide the upholsterer with overalls, safety shoes and other PPE:

cotton suit;
combined gloves;
leather boots;
goggles.

Permanently engaged in non-outdoor work in winter additionally:

jacket and trousers with insulating lining;
felt boots.

2. Safety requirements before starting work

2.1. Put on and tidy up your uniform.

2.2. Inspect the workplace, clear the passages and do not block them. If there are oil leaks, sprinkle this place with sawdust or sand and remove them.

2.3. Check and prepare tools and fixtures:

percussion tool - chisels, crosscuts, center punches should not have cracks, cold hardening;
hammers and sledgehammers should have a slightly convex, not knocked down, without cracks and work hardening surface of the striker;
the handles of hammers and sledgehammers must have a smooth surface, be made of hard and tough wood, firmly mounted and riveted with steel wedges. handles should not have cracks, knots, bundles;
the abrasive wheel of the grinding machine must not have chips, cracks, be correctly installed and fixed. The case must be grounded.

2.4. The tools and materials required for repair and tightening should be placed so that they do not interfere with work, do not block the passage, and cannot fall.

3. Safety requirements during work

3.1. Install the product in a special slipway, ensuring reliable fastening and the necessary passages.

3.2. When working with a grinder - use machines with special care. Have special safety goggles with side flaps. Protect the ejection zone of abrasive and metal burrs to avoid injury to other workers. Vibration is not allowed. circle.

3.3. Do not allow unauthorized persons not related to work to work without the permission of the master.

3.4. Timely fill the cutting edges of the tool, without reducing the optimal sharpening angles (to avoid twisting the drill).

3.5. Avoid burrs, nicks on the percussion instrument.

3.6. The workplace at the slipway must be kept clean, there should be no spilled oil, chips, waste of the workpiece, scraps of metal, material on the floor.

3.7. When aligning the holes and installing the bolts, do not insert your fingers into the aligned holes, use special barbs for this purpose.

3.8. Cutting the material is carried out on a special table, observing safety measures when working with a cutting tool.

3.9. The working surface of the table must be smooth.

3.10. Do not use when working cartridges with protruding stoppers, screws, bolts. If there are moving parts, they must be protected.

4. Safety requirements in emergency situations

4.1. Upon detection of broken electric cartridges, faulty switches, electrical wires with damaged insulation, as well as in all cases of electric shock, you must immediately inform the management to eliminate violations and provide first aid.

4.2. In the event of an accident or an accident, the upholsterer must:

switch off the portable power tool immediately;
provide first aid to the victim;
himself or through other workers to call an ambulance;
report the incident to the supervisor.

5. Safety requirements upon completion of work

5.1. Remove the product from the table and place on the spacers.

5.2. Tidy up the workplace, remove tools and fixtures, remove foreign objects and materials from the aisles.

5.3. Report all problems to the master.

We recommend interesting articles Section Standard instructions for labor protection:

▪ Argon welding electric welder. Standard instruction on labor protection

▪ Tractor driver and choker operator skidding the forest. Standard instruction on labor protection

▪ Testing of safety belts, portable ladders and ladders. Standard instruction on labor protection

See other articles Section Standard instructions for labor protection.

Read and write useful comments on this article.

<< Back

Latest news of science and technology, new electronics:

Artificial leather for touch emulation 15.04.2024

In a modern technology world where distance is becoming increasingly commonplace, maintaining connection and a sense of closeness is important. Recent developments in artificial skin by German scientists from Saarland University represent a new era in virtual interactions. German researchers from Saarland University have developed ultra-thin films that can transmit the sensation of touch over a distance. This cutting-edge technology provides new opportunities for virtual communication, especially for those who find themselves far from their loved ones. The ultra-thin films developed by the researchers, just 50 micrometers thick, can be integrated into textiles and worn like a second skin. These films act as sensors that recognize tactile signals from mom or dad, and as actuators that transmit these movements to the baby. Parents' touch to the fabric activates sensors that react to pressure and deform the ultra-thin film. This ... >>

Petgugu Global cat litter 15.04.2024

Taking care of pets can often be a challenge, especially when it comes to keeping your home clean. A new interesting solution from the Petgugu Global startup has been presented, which will make life easier for cat owners and help them keep their home perfectly clean and tidy. Startup Petgugu Global has unveiled a unique cat toilet that can automatically flush feces, keeping your home clean and fresh. This innovative device is equipped with various smart sensors that monitor your pet's toilet activity and activate to automatically clean after use. The device connects to the sewer system and ensures efficient waste removal without the need for intervention from the owner. Additionally, the toilet has a large flushable storage capacity, making it ideal for multi-cat households. The Petgugu cat litter bowl is designed for use with water-soluble litters and offers a range of additional ... >>

The attractiveness of caring men 14.04.2024

The stereotype that women prefer "bad boys" has long been widespread. However, recent research conducted by British scientists from Monash University offers a new perspective on this issue. They looked at how women responded to men's emotional responsibility and willingness to help others. The study's findings could change our understanding of what makes men attractive to women. A study conducted by scientists from Monash University leads to new findings about men's attractiveness to women. In the experiment, women were shown photographs of men with brief stories about their behavior in various situations, including their reaction to an encounter with a homeless person. Some of the men ignored the homeless man, while others helped him, such as buying him food. A study found that men who showed empathy and kindness were more attractive to women compared to men who showed empathy and kindness. ... >>

Random news from the Archive

Magnetic glue 10.03.2007

German chemists have created a glue whose properties are subject to a magnetic field.

In a colloidal solution of silicon dioxide (liquid glass, ordinary office glue), they mixed dusty iron oxide. The parts to be glued are exposed to a high-frequency alternating magnetic field, the iron oxide particles are heated, and the glue immediately sets.

If the connection needs to be glued, it is subjected to the same, but more powerful, alternating magnetic field, the glue is very hot, and the connection breaks up.

The only drawback of the new adhesive is that it is not suitable for electrically conductive materials.

Other interesting news:

▪ Octopus color

▪ Memristors - electronics of the future

▪ Detective on the phone

▪ Lexus RZ 450e electric crossover

▪ Silent boots over shoes

News feed of science and technology, new electronics

Interesting materials of the Free Technical Library:

▪ section of the site Microcontrollers. Article selection

▪ article A parable by the town. Popular expression

▪ article Which stone, according to the ancient Greeks, protects a person from intoxication? Detailed answer

▪ article Motorcycle tractor. Personal transport

▪ article Single-coil metal detector of induction type, theory. Encyclopedia of radio electronics and electrical engineering

▪ Article Hand snake. Focus Secret

Leave your comment on this article:

All languages of this page

Home page | Library | Articles | Website map | Site Reviews