Instructions for labor protection when working on a drilling machine type CITOBORMA

Free technical library

OCCUPATIONAL SAFETY AND HEALTH
Free library / Occupational Safety and Health / Standard instructions for labor protection

Instructions for labor protection when working on a drilling machine type CITOBORMA

Occupational Safety and Health

Occupational Safety and Health / Standard instructions for labor protection

Comments on the article

Safe Operation

1. General requirements for labor protection

1.1. Persons who have passed a medical examination and have no contraindications to work in this profession (specialty), introductory briefing and briefing at the workplace are allowed to work. Workers are allowed to work independently after an internship, verification of theoretical knowledge and acquired skills in safe ways of working. In the future, at the workplace, briefings on labor protection are held at least once every 3 months.

1.2. When transferring to a new job, from temporary to permanent, from one operation to another with a change in the technological process or equipment, employees must be instructed in labor protection at the workplace.

1.3. Conducting all types of briefings must be recorded in the Briefing Log with the obligatory signatures of the person who received and conducted the briefing.

1.4. Each employee is obliged to comply with the requirements of this instruction, labor and production discipline, work and rest regime, all requirements for labor protection, safe work performance, industrial sanitation, fire safety, electrical safety.

1.5. Smoking is allowed only in specially designated areas. The use of alcoholic beverages at work, as well as going to work in a state of alcoholic or drug intoxication, is prohibited.

1.6. When performing work, it is necessary to be attentive, not to be distracted by extraneous affairs and conversations, and not to distract others from work. It is forbidden to sit down and lean on random objects and fences.

1.7. It is forbidden to approach operating machines, installations, machines on which other workers work, and distract them with extraneous conversations, turn on or off (except in emergency cases) equipment, transport and lifting mechanisms, work on which is not assigned, go beyond the fences of hazardous areas, in zones of technological passages.

1.8. The employer is obliged to provide workers with overalls, safety shoes, as well as personal protective equipment in accordance with the work they perform and in accordance with applicable standards. It is forbidden to work without overalls, safety shoes and other personal protective equipment laid down in accordance with the standards.

1.9. Each employee needs:

know the place of storage of the workshop first-aid kit;
be able to provide first aid for work-related injuries.

1.10. It is allowed to store and eat food only in established and equipped places.

1.11. It is forbidden to be in production premises in outerwear, undress or hang clothes, hats, bags on equipment.

1.12. It is forbidden to clutter up passages, driveways, workplaces, approaches to shields with fire fighting equipment, fire hydrants and a common switch.

1.13. Spilled cleaners, lubricants, water, etc. on the floor. wipe off immediately.

1.14. Cleaning materials impregnated with oil, paint, solvent, put in tightly closed metal boxes. Do not scatter these materials, at the end of the shift they should be removed from the premises.

1.15. Store fuels, lubricants and flammable liquids only in a tightly closed metal container (box) or cabinet in an amount not exceeding the replacement rate. It is forbidden to leave combustible liquids and flammable liquids in the aisles, driveways and the working area of the equipment.

1.16. It is forbidden to repair equipment, fix electrical equipment and the electrical network to personnel who do not have access to these works, work near unshielded current-carrying parts, touch electrical wires, general lighting fittings, open doors of electrical cabinets, fencing of knife switches, switchboards and control panels.

1.17. Do not use lubricants for washing hands.

1.18. Finished products should be stacked carefully, on racks with a height of no more than 1,6 m from the floor (including the height of the rack).

1.19. It is forbidden to use faulty racks (pallets): with a faulty coating, with broken legs, etc., lean racks (pallets) against the machine frame or wall, as well as put them on the end, transfer, stack and disassemble the racks from a stack by one employee.

1.20. It is forbidden to use defective hand tools, as well as tools of inappropriate sizes, to scatter them around the equipment, in aisles, in driveways (keep tools and tools in specially designated places).

1.21. Perform only the work assigned by the head. It is forbidden to entrust the equipment to another person and to allow persons who are not related to the assigned work to the workplace.

1.22. It is forbidden to be in the production room after the end of work.

1.23. The employee is responsible in accordance with applicable law for compliance with the requirements of instructions, industrial injuries and accidents that occurred through his fault.

1.24. The control of the implementation of this instruction is assigned to the head of the department.

2. Safety requirements before starting work

2.1. Put on your uniform, put it in order.

2.2. Familiarize yourself with the entries in the Journal of the technical condition of the equipment. In case of any comments, do not start work until the troubleshooting and a note in the Journal (adjuster, electrician) about the health of the equipment.

2.3. Inspect equipment and work area. Prepare the necessary devices and tools for work, check their serviceability.

2.4. Check the serviceability of the machine at idle, paying attention to the operation of turning on, off, braking devices, as well as to the reliability of fixing the control handle, cleanliness and order in the workplace. Remove unnecessary items from the equipment (oil cans, rags, etc.).

2.5. Check and adjust workplace lighting.

2.6. Immediately report any shortcomings and malfunctions in the workplace to the work supervisor and do not start work until the troubleshooting and permission of the supervisor.

3. Safety requirements during work

3.1. CITOBORMA tabletop paper drilling machine must be installed on a flat, horizontal, hard surface, securely connected to the power supply.

3.2. Keep work area and equipment clean and tidy. Cutting tools should be sharp and securely fastened to the machine, spare tools should be stored in cases or cases.

3.3. Check the condition of the clamping device, the presence of a protective glass on the clamping device.

3.4. Check the correct installation of the drill, eliminate its runout and firmly fix it in the chuck. Make sure the spindle is held in the up position.

3.5. Set the working table of the machine and the stops to the required position, fix it securely.

3.6. All maintenance work on the machine: repair, cleaning, lubrication, tool change, removal of guards, reinstallation of the format should be performed only after the machine has been disconnected from the mains.

3.7. During the operation of the machine, it is prohibited:

touch the drill with your hands or any object;
tilt your head close to the cutting tool;
keep your fingers close to the lowered clamp;
carry out any repairs, repairs, cleaning or lubrication;
use additional devices (levers) to press the drill on the workpiece being processed.

3.8. When turning the workpiece together with the drill, in case of jamming or breakage of the tool, stop the machine immediately.

3.9. Remove dust and paper waste only after the machine has come to a complete stop.

4. Safety requirements in emergency situations

4.1. In case of fire, immediately turn off the equipment, turn off the power supply, with the exception of the lighting network. Report the fire to everyone working in the room, call the fire brigade and start extinguishing the fire with the available fire extinguishing equipment.

4.2. If voltage (sensation of current) is detected on the metal parts of the equipment, the ground wire is broken, the equipment should be immediately turned off, report to the foreman about the malfunction of the electrical equipment and do not start work without his instructions.

4.3. Disconnect the equipment from the network, stop working and notify the workshop administration in case of a malfunction of the equipment, safety, protective devices, as well as if there is a smell of burning and smoke, if foreign objects get into the equipment, if there is a power outage, vibration and noise.

4.4. In case of injury, first of all, release the victim from the traumatic factor, call for medical assistance, provide first aid to the victim, notify the work manager and save the traumatic situation until the causes of the incident are investigated.

5. Safety requirements at the end of work

5.1. Stop the equipment, turn off the general introductory switch, clean and tidy the workplace, make an entry in the Journal of the technical condition of the equipment.

5.2. Take off your clothes and put them in the closet.

5.3. Wash face and hands with warm water and soap.

We recommend interesting articles Section Standard instructions for labor protection:

▪ Work with the water pump. Standard instruction on labor protection

▪ Working with a jack. Standard instruction on labor protection

▪ Timber cargo loading and unloading. Standard instruction on labor protection

See other articles Section Standard instructions for labor protection.

Read and write useful comments on this article.

<< Back

Latest news of science and technology, new electronics:

Artificial leather for touch emulation 15.04.2024

In a modern technology world where distance is becoming increasingly commonplace, maintaining connection and a sense of closeness is important. Recent developments in artificial skin by German scientists from Saarland University represent a new era in virtual interactions. German researchers from Saarland University have developed ultra-thin films that can transmit the sensation of touch over a distance. This cutting-edge technology provides new opportunities for virtual communication, especially for those who find themselves far from their loved ones. The ultra-thin films developed by the researchers, just 50 micrometers thick, can be integrated into textiles and worn like a second skin. These films act as sensors that recognize tactile signals from mom or dad, and as actuators that transmit these movements to the baby. Parents' touch to the fabric activates sensors that react to pressure and deform the ultra-thin film. This ... >>

Petgugu Global cat litter 15.04.2024

Taking care of pets can often be a challenge, especially when it comes to keeping your home clean. A new interesting solution from the Petgugu Global startup has been presented, which will make life easier for cat owners and help them keep their home perfectly clean and tidy. Startup Petgugu Global has unveiled a unique cat toilet that can automatically flush feces, keeping your home clean and fresh. This innovative device is equipped with various smart sensors that monitor your pet's toilet activity and activate to automatically clean after use. The device connects to the sewer system and ensures efficient waste removal without the need for intervention from the owner. Additionally, the toilet has a large flushable storage capacity, making it ideal for multi-cat households. The Petgugu cat litter bowl is designed for use with water-soluble litters and offers a range of additional ... >>

The attractiveness of caring men 14.04.2024

The stereotype that women prefer "bad boys" has long been widespread. However, recent research conducted by British scientists from Monash University offers a new perspective on this issue. They looked at how women responded to men's emotional responsibility and willingness to help others. The study's findings could change our understanding of what makes men attractive to women. A study conducted by scientists from Monash University leads to new findings about men's attractiveness to women. In the experiment, women were shown photographs of men with brief stories about their behavior in various situations, including their reaction to an encounter with a homeless person. Some of the men ignored the homeless man, while others helped him, such as buying him food. A study found that men who showed empathy and kindness were more attractive to women compared to men who showed empathy and kindness. ... >>

Random news from the Archive

Biological magnetoreception 27.01.2021

Scientists have long suspected that because magnets can attract and repel electrons, the Earth's magnetic or geomagnetic field could influence animal behavior through chemical reactions. When certain molecules are excited by light, an electron can jump from one molecule to another and create two molecules with single electrons, known as radical pairs.

Single electrons can be in one of two different spin states. If two radicals have the same electron spin, their subsequent chemical reactions proceed slowly, while pairs of radicals with opposite electron spins can react faster. Magnetic fields can affect the spin states of electrons and thus directly affect chemical reactions involving radical pairs.

So the Japanese became interested in flavin molecules. They are a subunit of cryptochromes, which are molecules capable of glowing or fluorescence when exposed to blue light. These are important photosensitive molecules in biology.

When flavins are excited by light, they can either fluoresce or form radical pairs. This possibility means that the flavin fluorescence intensity depends on how fast the radical pairs react. Japanese researchers shone a laser at these molecules, but at the same time adding an artificial magnetic field, to understand how much this field affects chemical reactions and fluorescence.

Statistical analysis of the light intensity showed that the fluorescence of the cell decreased by about 3,5% each time the cells were placed in a magnetic field. This means that blue light induces flavin molecules to generate radical pairs, and therefore there were fewer molecules that could emit light. The flavin fluorescence in the cell decreased until the magnetic field disappeared.

Scientists believe that the very weak magnetic field of the Earth has a biologically important effect on the chemical processes occurring in a living organism. And this is already magnetoreception - that is, the ability to feel a magnetic field, and thanks to this, navigate in space.

Other interesting news:

▪ Brain implant for memory recovery

▪ Smartphone Lenovo Z6 Pro

▪ BGA5L1BN6 - low noise amplifier for the 868 MHz band

▪ DNA from the air

▪ Exciton transistor

News feed of science and technology, new electronics

Interesting materials of the Free Technical Library:

▪ section of the site The most important scientific discoveries. Article selection

▪ article Non-freezing plumbing. Tips for the home master

▪ article When did man start domesticating animals? Detailed answer

▪ Mais article. Legends, cultivation, methods of application

▪ article Making a fuse from wire for any current. Encyclopedia of radio electronics and electrical engineering

▪ article Disappearance of pigeons. Focus Secret

Leave your comment on this article:

All languages of this page

Home page | Library | Articles | Website map | Site Reviews