OCCUPATIONAL SAFETY AND HEALTH
Instructions on labor protection for the piler-dumper of sleeper ridges Occupational Safety and Health / Standard instructions for labor protection Safe Operation 1. General requirements for labor protection General labor protection requirements are set out in the instructions "General requirements for labor protection for workers engaged in logging and forestry work". 2. Labor protection requirements before starting work 2.1. Tidy up work clothes (fasten all buttons, put hair under a headdress and put on mittens). 2.2. Before starting work, make sure:
2.3. If workplaces are cluttered with sawdust, bark, or debris, they must be cleaned. Sprinkle icy areas in the workplace with sand, slag, ash or other anti-slip substances. 3. Labor protection requirements during work 3.1. The employee must perform only the work that is entrusted to him by his immediate supervisor. 3.2. Dismantling of bundles of logs delivered to the receiving area should be started only after unloading, uncoupling of slings and moving lifting machines or devices to a safe (at least 5 m) distance. 3.3. When rolling a pack of logs, it is forbidden to climb it. Being on the side of the ends of the logs, you should first roll up the upper and outermost unengaged logs, while simultaneously supporting and guiding the logs in contact with them. Logs that impede the movement of others should be rolled away first. 3.4. It is not allowed to hold logs rolling from a height with your hands, to substitute your foot. 3.5. Logs should be rolled over the site and sleeper ridges should be rolled onto a timber conveyor or trolley, being from the side of the ends of the logs. 3.6. When moving logs, take a stable position. 3.7. When working together, you need to coordinate your actions with a partner. 3.8. Before starting the timber conveyor, it is necessary to give a sound signal, make sure that there are no people in the danger zone, and only then turn on the conveyor. 3.9. Sleeper ridges must be fed sequentially to the longitudinal timber conveyor. It is impossible to allow simultaneous engagement of two or more assortments by traverses. 3.10. The ridge should be rolled up to the trolley of the sleeper machine, taking into account the location of the pilers and warn them. 3.11. The ridges should be dropped from the timber conveyor from the side opposite to their fall. 3.12. Stop work immediately and turn off the conveyor:
3.13. It is forbidden:
3.14. It is necessary to cross the timber transporters only through special bridges, ladders, ladders. 4. Labor protection requirements in emergency situations 4.1. If motors overheat, stop them and allow them to cool down. Do not cool engines with water or snow. 4.2. If a fire is detected in the electrical wiring, it is necessary to immediately stop the engine and turn off the breaker. 4.3. When a stop signal is received from any person, timber trucks or other equipment must be stopped. You can not start work until there is complete confidence in the safety. 4.4. In the event of a fire, ignition, it is necessary to immediately inform the fire brigade, start extinguishing the fire with the available fire extinguishing equipment and take measures to call the immediate supervisor to the fire site. 4.5. The victim or eyewitness must notify the foreman or the appropriate work manager of each accident. 4.6. Each worker must be able to provide first aid. Assistance must be provided immediately at the scene of the incident. The first step is to eliminate the source of injury (turn off the engine, stop the mechanism, release the victim, etc.). The provision of assistance should begin with the most significant that threatens the health or life of a person: in case of severe bleeding, apply a tourniquet, and then bandage the wound; if a closed fracture is suspected, apply a splint; with open fractures, you should first bandage the wound, and then apply a splint; for burns, apply a dry bandage; in case of frostbite, gently rub the affected area using soft or fluffy tissues. If spinal injuries are suspected, the victim can only be transported in the supine position on a rigid base. After providing first aid, the victim should be sent to the nearest medical facility. 5. Labor protection requirements at the end of work 5.1. Upon completion of work, you must:
5.2. Report to the shifter or foreman about the condition of the equipment and any malfunctions identified during operation. 5.3. Any deficiencies in the field of labor protection must be reported to the foreman or the relevant work manager. We recommend interesting articles Section Standard instructions for labor protection: ▪ Weaver. Standard instruction on labor protection ▪ Washing machine operator (dishwasher). Standard instruction on labor protection ▪ Gantry crane operator. Standard instruction on labor protection See other articles Section Standard instructions for labor protection. Read and write useful comments on this article. Latest news of science and technology, new electronics: Artificial leather for touch emulation
15.04.2024 Petgugu Global cat litter
15.04.2024 The attractiveness of caring men
14.04.2024
Other interesting news: ▪ Orbital lunar probe LADEE crashed as planned ▪ MediaTek MT6589 single-chip system ▪ Eternal paint based on plasmonic pixels News feed of science and technology, new electronics
Interesting materials of the Free Technical Library: ▪ section of the site Winged words, phraseological units. Selection of articles ▪ article A series of magical changes to a cute face. Popular expression ▪ article What role did Russian emigrants play in the development of US aviation? Detailed answer ▪ article Sailboat made of logs. Personal transport ▪ article Cement for amber. Simple recipes and tips
Leave your comment on this article: All languages of this page Home page | Library | Articles | Website map | Site Reviews www.diagram.com.ua |