OCCUPATIONAL SAFETY AND HEALTH
Instructions on labor protection for the acceptor of orders. Full document Occupational Safety and Health / Standard instructions for labor protection Safe Operation 1. General safety requirements 1.1. Persons who have studied the safety instructions and have been instructed at the workplace are allowed to work on receiving orders. 1.2. The order taker should be issued with the following personal protective equipment: cotton gown for 12 months. 1.3. Perform only the work assigned by the administration. 1.4. It is forbidden to work on faulty equipment, faulty devices and fixtures. 1.5. It is forbidden to smoke at the workplace and in the production area. Smoking only in specially equipped places. 1.6. If a dangerous or harmful production factor is detected, warn workers and immediately inform the administration. 1.7. Know how to help the victim in an accident. 1.8. In case of injury, contact the nearest medical facility and report the incident to the administration. 1.9. Employees are required to know and comply with the internal regulations, not to allow the use of alcoholic, narcotic and toxic substances, smoking in places other than those specified. 2. Safety requirements before starting work 2.1. Tidy up clothes, fasten buttons. 2.2. Check the stability and serviceability of the table, chairs, cabinets and other furniture. 2.3. Check the serviceability of electrical equipment, devices (supplying electrical wires, sockets, plugs, switches, etc.). 2.4. Arrange the items you need to work in an order that is easy to use. 3. Safety requirements during work 3.1. When accepting orders for the repair of clothing, it is necessary to ensure that the clothing is clean and that there are no foreign (piercing and cutting) objects in the pockets. 3.2. When working at a desk, it is necessary to keep the body in the correct position. It is forbidden to swing on a chair to avoid injury. 3.3. Be careful when working with cutting and stabbing tools (knives, scissors, blades, needles, pins, etc.). 3.4. Cutting and piercing tools should be in a specially designated place. It is forbidden to put them in your pocket. 3.5. When working with a needle, you must use a thimble. 3.6. Keep the workplace clean throughout the working day, do not clutter up with materials and products. 4. Safety requirements in an emergency 4.1. In the event of an accident or a situation that may lead to an accident, you must: 4.1.1. Stop work. 4.1.2. Report the incident to the administration. 4.1.3. Take measures to help the injured, if necessary, call an ambulance. 4.1.4. Take measures to eliminate an accident or a situation that may lead to an accident through the administration and relevant services. 5. Safety requirements at the end of work 5.1. Disconnect all electrical equipment from the mains. 5.2. tidy up the workplace. Wash face and hands with warm water and soap. We recommend interesting articles Section Standard instructions for labor protection: ▪ Machinist for cutting and filling seams. Standard instruction on labor protection ▪ Work with mineral fertilizers and pesticides. Standard instruction on labor protection ▪ Working with pyrotechnic tools. Standard instruction on labor protection See other articles Section Standard instructions for labor protection. Read and write useful comments on this article. Latest news of science and technology, new electronics: Artificial leather for touch emulation
15.04.2024 Petgugu Global cat litter
15.04.2024 The attractiveness of caring men
14.04.2024
Other interesting news: ▪ Smart bracelet will track the composition of sweat ▪ Samsung Gear VR Innovator Edition - virtual reality glasses for smartphones ▪ Laser interceptors will protect the Earth from asteroids ▪ A new kind of computer sport ▪ Smartphone vibration motor for wiretapping News feed of science and technology, new electronics
Interesting materials of the Free Technical Library: ▪ site section Power Amplifiers. Article selection ▪ article 3D pictures (anaglyph). Encyclopedia of visual illusions ▪ article Who Invented Shoes? Detailed answer ▪ article Intellectual property appraiser. Job description ▪ article Lubricant used when cutting screws. Simple recipes and tips
Leave your comment on this article: Comments on the article: a guest Written in the old style. All languages of this page Home page | Library | Articles | Website map | Site Reviews www.diagram.com.ua |