OCCUPATIONAL SAFETY AND HEALTH
Instructions on labor protection for the stamper of labels. Full Document Occupational Safety and Health / Standard instructions for labor protection Safe Operation 1. General requirements for labor protection 1.1. Each worker, upon entering a job, must undergo an introductory general safety briefing, and when transferring him from one job to another (at least for a short time), as well as from one workshop to another, he must undergo a safety briefing at that workplace from the foreman which he will serve. 1.2. Persons at least 18 years of age who have passed a medical examination, have been trained in safe methods and labor practices when stamping labels, have studied the safety instructions and have been instructed at the workplace are allowed to permanently work as a label stamper. 1.3. An unprotected feed mechanism and a matrix of machines (automatic machines) serviced by a label stamper can cause mechanical injury. Inattentive operation may cause electrical injury. 1.4. When accepting a shift, require the shifter to hand over the workplace in a clean and working condition, as well as equipment. 1.5. The worker is obliged to study and improve the methods of safe work. 1.6. Perform only assigned work. 1.7. For non-compliance with this instruction, the worker is subject to disciplinary liability in accordance with the rules of the internal labor procedure. 2. Labor protection requirements before starting work 2.1. Make sure that work clothes are in good condition, put your hair under a headdress. 2.2. Check your workspace and make sure it is adequately lit and not cluttered. 2.3. Make sure that the machine, its starting devices, and the safety of the protective devices are in good condition. 2.4. Check by external inspection the presence and fastening of the ground wire, make sure that there are no bare wires. 2.5. Fill the rake (device containing ink) with ink and turn on the machine for smearing with ink, printing rollers for 5-10 minutes. 2.6. Put the labels into the hopper (having previously stretched the pack of labels, thus preventing the labels pressed between themselves from getting under the matrix. 2.7. Check that labels are fed smoothly with the hopper counterweight. 2.8. Fill the matrix with the pin and insert into the machine. 2.9. Set the dial of the circulation mechanism to the number of the required number of labels. 3. Labor protection requirements during work 3.1. When refilling the matrices, the machine must be turned off, wait for the mechanisms to stop completely. Do not apply artificial braking mechanisms. 3.2. When the signal light comes on, you must stop the machine and fill the hopper with labels. 3.3. In case of matrix clogging, wash off excess paint with acetone using a brush, while turning on the exhaust fan in the workshop. 3.4. Stay calm and allow yourself to be distracted while operating the label press. 3.5. It is forbidden to clean, lubricate the mechanisms while the machine is running, as well as refill the paint into the rake (a device containing paint). 3.6. When cleaning the machine, do not touch the electrical wires, and when lubricating, make sure that oil does not get on the wires. 3.7. It is forbidden to pull out or adjust the labels with your hands while the machine is running. To fill the hopper with labels - turn off the machine. 3.8. Do not repair the equipment yourself. In the event of a malfunction, turn off the power supply and call a repairman. 3.9. Monitor the correct operation of the exhaust ventilation of the production room. 4. Labor protection requirements in emergency situations 4.1. In case of an emergency, stop work, leave the danger zone, if necessary, remove people nearby. 4.2. In the event of a fire, immediately call the fire brigade by phone 01, remove people to a safe place. Report the fire to management. 4.3. Provide first aid to victims in case of injury and call an ambulance or send the victim to a first-aid post, inform the head. 5. Labor protection requirements at the end of work 5.1. Turn off the machine, rinse the apparatus and matrix with acetone until the paint is completely removed. 5.2. Hand over the carefully cleaned workplace to the shift worker and inform the foreman about the shortcomings noticed during the work. 5.3. Take personal hygiene measures. We recommend interesting articles Section Standard instructions for labor protection: ▪ Crusher. Standard instruction on labor protection ▪ Cleaning of fuel tanks. Standard instruction on labor protection ▪ Household worker. Standard instruction on labor protection See other articles Section Standard instructions for labor protection. Read and write useful comments on this article. Latest news of science and technology, new electronics: Artificial leather for touch emulation
15.04.2024 Petgugu Global cat litter
15.04.2024 The attractiveness of caring men
14.04.2024
Other interesting news: ▪ Octospot - action camera for diving enthusiasts ▪ Replaceable batteries should become a European standard News feed of science and technology, new electronics
Interesting materials of the Free Technical Library: ▪ section of the site For a beginner radio amateur. Article selection ▪ article Whatever a fool does, he does everything wrong. Popular expression ▪ article Which fish shoot down insects with spitting? Detailed answer ▪ article car wash. Job description ▪ article January-4. Throttle body. Encyclopedia of radio electronics and electrical engineering ▪ Article Experience with extinguished candle. physical experiment
Leave your comment on this article: All languages of this page Home page | Library | Articles | Website map | Site Reviews www.diagram.com.ua |