OCCUPATIONAL SAFETY AND HEALTH
Instruction on labor protection for the measurer, inspector of materials, patterns, products. Full document Occupational Safety and Health / Standard instructions for labor protection Safe Operation 1. General safety requirements 1.1. When applying for a job, each worker must undergo an introductory, general safety briefing, and when transferring him from one job to another (at least for a short time), as well as from one workshop to another, he must undergo a safety briefing from the foreman at that worker. the place it will serve. 1.2. Persons at least 18 years of age who have been trained in safe methods and techniques of work on probing machines or tables to control the length and width of various materials, who have studied the instructions on labor protection and have been instructed at the worker, are allowed to work independently as inspectors of materials, patterns and products, measurers. place. 1.3. Dangerous places of probing tables are:
1.4. The inspector of materials and products (measurer) is obliged to: 1.5. Learn and improve safe working practices. 1.6. Perform only assigned work. 1.7. For non-compliance with this instruction, the perpetrators are subject to disciplinary liability in accordance with the internal labor regulations. 1.8. Machines for measuring and sorting fabric must have a device that prevents the rolls from being ejected from the bearings. 1.9. Machines for sorting fabrics must be equipped with daylight fixtures that provide normal illumination and a uniform light flux on the working surface. 1.10. Grading and measuring, control and measuring machines and tables must be equipped with devices for removing static electricity (ionizers). 1.11. The frosted glass of grading and probing machines must be cut flush with its surface and provided with uniform illumination. 1.12. Rail tracks for mechanical trolleys should be installed strictly horizontally, the rail heads should be recessed flush with the floor. 1.13. Starting devices of machines should be concentrated in one place. 1.14. Push-button stop stations should provide the ability to turn off the machine by both operating machines serving the machine from 2 sides and equipped with sound and light alarms warning about the start of the machine. 2. Labor protection requirements before starting work 2.1. Make sure your work clothes are in good condition. Remove hair under headgear 2.2. Check your workplace; make sure it is adequately lit and not cluttered. 2.3. Check by external inspection the presence and fastening of the ground wire and make sure that there are no bare wires. 2.4. Check the serviceability of the rolling and rolling device of the mechanized table and the operation of the chalk marker (idling), the presence and serviceability of the gearbox housing and gear guards. 2.5. Filling the fabric, straightening it on the rolling and rolling devices should be carried out only with the electric motor turned off. 2.6. When straightening the edges of the fabric on the table, do not bring your hands close to the chalk marker. 2.7. To prevent rolls of fabric from falling, securely fasten their rollers in the slots of the unwinder and rewinder. 2.8. Do not open or remove the protective cover of the gear guard reducer. 2.9. In case of any malfunction, turn off the electric motor, inform the foreman or other head of the department. 2.10. Do not leave the unroller and rewinder turned off unattended. 3. Labor protection requirements in emergency situations 3.1. In case of injury at work, immediately contact the first-aid post and inform the foreman or other head of the department about the accident. 3.2. Provide the necessary assistance to the victim at work and inform the foreman or other head of the department about the accident. 4. Labor protection requirements at the end of work 4.1. Switch off and after stopping clean the unwinder and rewinder. 4.2. Thoroughly clean the machine and clean the workplace, hand it over to the shifter and inform him of your comments and shortcomings during work. 4.3. Take personal hygiene measures. We recommend interesting articles Section Standard instructions for labor protection: ▪ Plumber. Standard instruction on labor protection ▪ Storage and operation of gas cylinders. Standard instruction on labor protection ▪ Work on string-casting typesetting machines. Standard instruction on labor protection See other articles Section Standard instructions for labor protection. Read and write useful comments on this article. Latest news of science and technology, new electronics: Artificial leather for touch emulation
15.04.2024 Petgugu Global cat litter
15.04.2024 The attractiveness of caring men
14.04.2024
Other interesting news: ▪ spy eye News feed of science and technology, new electronics
Interesting materials of the Free Technical Library: ▪ section of the site Calls and audio simulators. Article selection ▪ spaceport article. History of invention and production ▪ article Auditor. Job description ▪ article Brown mordant for iron and steel things. Simple recipes and tips ▪ article Solar cells and modules. Encyclopedia of radio electronics and electrical engineering
Leave your comment on this article: Comments on the article: Vyacheslav Not written by an expert. You don’t need to tell the shift worker about your shortcomings about FROM NO general briefing - it sounds like that in the text. About malfunctions and identified deviations during operation, yes, you need .... All languages of this page Home page | Library | Articles | Website map | Site Reviews www.diagram.com.ua |