OCCUPATIONAL SAFETY AND HEALTH
Instructions on labor protection for a locksmith-picker. Full document Occupational Safety and Health / Standard instructions for labor protection Safe Operation 1. General safety requirements 1.1. A picker for the maintenance and assembly of buses performs disassembly, repair, assembly of vehicle components, and maintenance work using a special tool. 1.2. During the work of a bus assembly fitter, hazardous production factors can be:
1.3. Persons at least 18 years of age who have passed a medical examination, trained in safe working methods and techniques, as well as trained in first aid for victims of accidents, who have passed an exam in the qualification commission of the enterprise and have been instructed in safety are allowed to work as a fitter for servicing and assembling buses . Admission to independent work is issued by order of the enterprise. 1.4. The following personal protective equipment is required for the fitter-purchaser for the maintenance and assembly of buses: cotton suit, leather boots, combined gloves, goggles, protective helmet. 1.5. The locksmith for the maintenance and assembly of buses is obliged to comply with the internal labor regulations. 1.6. Persons who do not comply with the requirements of this instruction violate production discipline and are subject to disciplinary liability. 2. Safety requirements before starting work 2.1. Starting work after vacation, as well as when receiving work that is not included in the scope of duties. It is necessary to require additional instruction from the leader. 2.2. It is necessary to properly wear the clean and serviceable overalls and safety shoes that rely on the norms. Hair must be removed under a headdress, do not keep metal objects with sharp ends in the pockets of clothing. Overalls must be fastened with all buttons and must not have developing ends. It is forbidden to roll up the sleeves of overalls. 2.3. Get an assignment from the work manager. 2.4. Prepare proper personal protective equipment. When working in the inspection hole, wear a protective helmet. 2.5. Prepare the workplace for safe work, it must be clean and free of foreign objects, with sufficient lighting. Portable lighting voltage - 12 V. 2.6. Check the serviceability of the tool, fixtures, guards, hoses. 3. Safety requirements during work 3.1. Work only on the equipment to which there is a permit, perform only the work that is entrusted to the head. 3.2. Keep your workplace clean and tidy during all working hours and do not clutter it with garbage. 3.3. The complete set of units and individual units for the assembly of buses should be carried out only in accordance with the technological map. 3.4. When completing the assembly of components and assemblies for the assembly of buses, it is prohibited:
3.5. Before starting work with lifting mechanisms, make sure that it is in good condition and that the weight of the unit being lifted corresponds to the lifting capacity of the mechanism, 4. Safety requirements in emergency situations 4.1. Upon detection of equipment defects that pose a danger to human life and equipment integrity. stop work immediately and report to the work manager. 4.2. In emergency situations, stop work, leave the danger zone. If there is a danger of an accident, take measures to prevent it, report the incident to the work manager. 4.3. In the event of a fire, immediately call the fire brigade, remove people and, if possible, combustible substances to a safe place, and start extinguishing the fire with the available primary fire extinguishing equipment. Report the fire to the manager. 4.4. Provide first aid to victims of injury, sudden illness, inform the head of work about an accident. 5. Safety measures at the end of work 5.1. After working in the inspection hole, remove all materials, tools and all foreign objects. 5.2. Clean the tools, fixtures, PPE and put them in the place provided for them. 5.3. Take off your overalls, put them in the closet. 5.4. Wash hands with warm soapy water or take a shower. 5.5. About all problems. Found during work and on the measures taken to eliminate them, report to the head of work. We recommend interesting articles Section Standard instructions for labor protection: ▪ Working with an electric chain saw. Standard instruction on labor protection ▪ Locksmith for the repair of technological installations. Standard instruction on labor protection See other articles Section Standard instructions for labor protection. Read and write useful comments on this article. Latest news of science and technology, new electronics: Artificial leather for touch emulation
15.04.2024 Petgugu Global cat litter
15.04.2024 The attractiveness of caring men
14.04.2024
Other interesting news: ▪ Data storage time in SSD increased thousands of times ▪ PLM-40E - 40W Step Dimming LED Driver ▪ Billionth mouse from Logitech ▪ The serious impact of the Internet on the brain ▪ The smallest twin-engine turbojet aircraft News feed of science and technology, new electronics
Interesting materials of the Free Technical Library: ▪ site section Parameters of radio components. Article selection ▪ article In the hope of glory and goodness. Popular expression ▪ article Was the first computer bug a real insect? Detailed answer ▪ article Buchu mountain. Legends, cultivation, methods of application ▪ article Solar Ponds. Encyclopedia of radio electronics and electrical engineering
Leave your comment on this article: All languages of this page Home page | Library | Articles | Website map | Site Reviews www.diagram.com.ua |