ENCYCLOPEDIA OF RADIO ELECTRONICS AND ELECTRICAL ENGINEERING Fluxes, pastes, inks, varnishes. Encyclopedia of radio electronics and electrical engineering Encyclopedia of radio electronics and electrical engineering / Ham Radio Technologies FLUXES: FTBF - for soldering aluminum and most of its alloys, stainless steels, copper and its alloys, nickel, cadmium, lead, platinum group metals. Activity temperature 200...320С. Removed with water. 38Н - for soldering nichrome, beryllium bronze, constantan, carbon and corrosion-resistant steels, nickel, copper and its alloys. Activity temperature 300...390С. Removed with water. FCA - for soldering copper, nickel and their alloys, zinc and carbon steels, has increased activity and ensures high quality of soldered joints when working with low-alloy steel grades. Activity temperature 160...350 C. Removed with water. IEC - for soldering electronic components of printed circuit boards, allows tinning with low-temperature solders without preliminary stripping. Activity temperature 200...330 C. Removed with water. The flux is non-toxic, non-corrosive, and non-flammable. FDGL - rosin-free glycerin flux. It is intended for the soldering of steel, nickel, copper and its alloys without preliminary cleaning. Activity temperature 150...300С. Removed with water. LTI-120 (alcohol rosin) - for soldering copper and its alloys, carbon steel, nickel, effective when soldering electronic components. Activity temperature 200...300С. It is removed with alcohol or an alcohol-gasoline mixture. FCT - for soldering electronic components of printed circuit boards with low-temperature solders without pre-cleaning. Activity temperature 160...300 C. Removed with water. Solder POS-61. The volume of 20 cm3 costs 1 hryvnia. 90 kop. Delivery of 0,5 l is possible. The flux is non-toxic, non-corrosive, and non-flammable. A distinctive feature of this flux is a very low cost. FCS - rosin-free neutral flux, designed for soldering parts of radio equipment, steel, nickel, copper and their alloys. Activity temperature 180...350С. The soldering is made by POS-61 solder. Flux residues are washed off with water or alcohol. FGA - designed for soldering steel, nickel, copper and its alloys without pre-cleaning. The soldering is made by POS-61 solder. Activity temperature 150...300 С Flux residues are washed off with water. TAGS - for soldering electronic components of printed circuit boards, allows tinning of boards with low-temperature solders without preliminary cleaning of the tinning surface. The activity temperature is 200...330 C. Soldering is performed with POS-61 solder. The flux is non-toxic, non-corrosive, and non-flammable. If necessary, the flux residues are washed off with water. In addition, sellers can supply all the listed fluxes filled in markers with a writing part diameter of 6,0 mm and 2,0 mm. The main difference from imported ones is that due to a more competent selection of the consistency on the writing surface, there are no hardening drops that need to be cleaned off. PASTES: KTP-19 - heat-conducting non-drying paste, designed to improve thermal contact between heated parts and the surface of the cooling radiator. It looks like a viscous, pasty mass of light gray color. Thermal conductivity 0,8...1,1 W/m deg. Specific volume electrical resistance is not less than 10 Ohm/cm. The dielectric loss tangent is not more than 0,02 at a frequency of 1 MHz. Dielectric constant 4,5 at the same frequency. Retention of plasticity for at least 10 years. Soldering - designed for group soldering of radioelements by surface mounting in a hot air environment. Applying the paste to the soldering zones is possible using a stencil method. Can also be used with a soldering iron. No pre-cleaning required. Residues are washed off with alcohol or water. INK: CS-2 (1) For drawing a printed circuit board pattern on a metal surface with a pen, ink liner, felt-tip pen or capillary pen for subsequent etching with an aqueous solution of ferric chloride. The working temperature of the solution is 80 C. Washing - any alcohol-containing solution. LUCKY: Varnish TLS For applying (restoring) contact conductive surfaces on a rubber base. Hardening time at 18CC no more than 20 minutes. See other articles Section Ham Radio Technologies. Read and write useful comments on this article. Latest news of science and technology, new electronics: Artificial leather for touch emulation
15.04.2024 Petgugu Global cat litter
15.04.2024 The attractiveness of caring men
14.04.2024
Other interesting news: ▪ Single Board PC Orange Pi Prime ▪ Direct lithography of optical systems based on perovskite ▪ Xiaomi Fire Extinguisher Bottle News feed of science and technology, new electronics
Interesting materials of the Free Technical Library: ▪ section of the site Art video. Article selection ▪ article The customer is always right. Popular expression ▪ article Dombay glade. Nature miracle ▪ article Six dollars in hand. Focus Secret
Leave your comment on this article: All languages of this page Home page | Library | Articles | Website map | Site Reviews www.diagram.com.ua |