Automatic charger. Scheme, description

Free technical library

ENCYCLOPEDIA OF RADIO ELECTRONICS AND ELECTRICAL ENGINEERING
Free library / Schemes of radio-electronic and electrical devices

Automatic charger. Encyclopedia of radio electronics and electrical engineering

Free technical library

Encyclopedia of radio electronics and electrical engineering / Chargers, batteries, galvanic cells

Comments on the article

The device allows not only charging, but also restoring batteries with sulfated plates due to the use of asymmetric current when charging in the charge (5 A) - discharge (0,5 A) mode for the full period of the mains voltage. The device also provides the ability to speed up the charging process if necessary.

This device has a number of features that make it easy to use. So, at the end of the charge, the circuit will automatically disconnect the battery from the charger. And if you try to connect a faulty battery (with a voltage below 7 V) or a battery with the wrong polarity, the circuit will not turn on in charge mode, which will protect the charger and battery from damage.

In the event of a short circuit of the X1 (+) and X2 (-) terminals, the FU1 fuse will blow during operation of the device.

The electrical circuit (Fig. 4.4) consists of a current stabilizer on a transistor VT1, a control device on a comparator D1, a thyristor VS1 for fixing the state and a key transistor VT2 that controls the operation of the relay K1.

Rice. 4.4. Automatic charger (click to enlarge)

When the device is turned on with the SA1 toggle switch, the HL2 LED will light up, and the circuit will wait until we connect the battery to terminals X1, X2. With the correct polarity of the battery connection, a small current flowing through the VD7 diode and resistors R14, R15 to the VT2 base will be sufficient for the transistor to open and relay K1 to operate.

When the relay is turned on, the transistor VT1 starts working in the current stabilizer mode - in this case, the HL1 LED will light up. The stabilization current is set by the resistor values in the VT1 emitter circuit, and the reference voltage for operation is obtained on the HL1 LED and the VD6 diode.

The current stabilizer operates on one half-wave of the mains voltage. During the second half-wave diodes VD1, VD2 are closed and the battery is discharged through the resistor R8. The value of R8 is chosen so that the discharge current is 0,5 A. It has been experimentally established that the optimal mode is the charge current of 5 A, the discharge is 0,5 A.

While the discharge is in progress, the comparator monitors the voltage on the battery, and if the value of 14,7 V is exceeded (the level is set by setting the resistor R10), it will turn on the thyristor. In this case, the LEDs HL3 and HL2 will start to glow. The thyristor shorts the base of the transistor VT2 through the VD9 diode to a common wire, which will turn off the relay. The relay will not turn on again until the button is pressed. RESET (SB1) or the whole circuit is not switched off for some time (SA1).

For stable operation of the D1 comparator, its power supply is stabilized by the VD5 zener diode. In order for the comparator to compare the voltage on the battery with the threshold voltage (set at input 2) only at the moment when the discharge is made, the threshold voltage by the circuit of the VD3 diode and the resistor R1 rises for the duration of the battery charge, which will prevent its operation. When the battery is discharged, this circuit is not involved in the work.

In the manufacture of the design, the transistor VT1 is installed on a radiator with an area of at least 200 square meters. see Power circuits from terminals X1, X2 and transformer T1 are made with a wire with a cross section of at least 0,75 square meters. mm.

The circuit uses capacitors C1 of the K50-24 type for 63 V, C2 - K53-4A for 20 V, a tuning resistor of the R10 type. SP5-2 (multi-turn), fixed resistors R2.R4 type C5-16MV, R8 type PEV-15, the rest - type C2-23. Relay K1 is suitable for any, with an operating voltage of 24 V and a permissible current through the contacts of 5 A; toggle switches SA1, SA2 type T1, button SB1 type KM1-1.

To adjust the charger, you will need a constant voltage source with a tuning range from 3 to 15 V. It is convenient to use the connection diagram shown in fig. 4.5.

Automatic charger
Rice. 4.5. Connection diagram for setting up the charger.

We begin the setting by selecting the value of the resistor R14. To do this, we supply a voltage of 1 V from the power supply A7 and by changing the value of the resistor R14 we achieve that the relay K1 operates at a voltage of at least 7 V. After that, we increase the voltage from the source. A1 to 14,7 V and adjust the comparator threshold with resistor R10 (to return the circuit to its original state after turning on the thyristor, press the SB1 button). It may also be necessary to select the resistor R1.

Lastly, we set up the current stabilizer. To do this, we temporarily install a pointer ammeter with a scale of 1 ... 0 A into the open circuit of the VT5 collector at point "A". By selecting resistor R4, we achieve readings on the ammeter of 1,8 A (for a current amplitude of 5 A), and after that, with SA2 turned on set R4, value 3,6 A (for a current amplitude of 10 A).

The difference in the reading of the pointer ammeter and the actual value of the current is due to the fact that the ammeter averages the measured value over the period of the mains voltage, and the charge is made only during half the period.

In conclusion, it should be noted that the final adjustment of the stabilizer current is best done on a real battery in steady state - when the transistor VT1 has warmed up and the effect of current growth due to a change in the junction temperature in the transistor is not observed. On this setting can be considered complete.

As the battery charges, the voltage on it will gradually increase, and when it reaches a value of 14,7 V, the circuit will automatically turn off the charge circuits. Automation will also turn off the charging process in case of some other unforeseen influences, for example, in the event of a breakdown of VT1 or a power outage. The auto-off mode can also be triggered by poor contact in the circuits from the charger to the battery. In this case, the RESET button (SB1) must be pressed.

Author: Shelestov I.P.

See other articles Section Chargers, batteries, galvanic cells.

Read and write useful comments on this article.

<< Back

Latest news of science and technology, new electronics:

Machine for thinning flowers in gardens 02.05.2024

In modern agriculture, technological progress is developing aimed at increasing the efficiency of plant care processes. The innovative Florix flower thinning machine was presented in Italy, designed to optimize the harvesting stage. This tool is equipped with mobile arms, allowing it to be easily adapted to the needs of the garden. The operator can adjust the speed of the thin wires by controlling them from the tractor cab using a joystick. This approach significantly increases the efficiency of the flower thinning process, providing the possibility of individual adjustment to the specific conditions of the garden, as well as the variety and type of fruit grown in it. After testing the Florix machine for two years on various types of fruit, the results were very encouraging. Farmers such as Filiberto Montanari, who has used a Florix machine for several years, have reported a significant reduction in the time and labor required to thin flowers. ... >>

Advanced Infrared Microscope 02.05.2024

Microscopes play an important role in scientific research, allowing scientists to delve into structures and processes invisible to the eye. However, various microscopy methods have their limitations, and among them was the limitation of resolution when using the infrared range. But the latest achievements of Japanese researchers from the University of Tokyo open up new prospects for studying the microworld. Scientists from the University of Tokyo have unveiled a new microscope that will revolutionize the capabilities of infrared microscopy. This advanced instrument allows you to see the internal structures of living bacteria with amazing clarity on the nanometer scale. Typically, mid-infrared microscopes are limited by low resolution, but the latest development from Japanese researchers overcomes these limitations. According to scientists, the developed microscope allows creating images with a resolution of up to 120 nanometers, which is 30 times higher than the resolution of traditional microscopes. ... >>

Air trap for insects 01.05.2024

Agriculture is one of the key sectors of the economy, and pest control is an integral part of this process. A team of scientists from the Indian Council of Agricultural Research-Central Potato Research Institute (ICAR-CPRI), Shimla, has come up with an innovative solution to this problem - a wind-powered insect air trap. This device addresses the shortcomings of traditional pest control methods by providing real-time insect population data. The trap is powered entirely by wind energy, making it an environmentally friendly solution that requires no power. Its unique design allows monitoring of both harmful and beneficial insects, providing a complete overview of the population in any agricultural area. “By assessing target pests at the right time, we can take necessary measures to control both pests and diseases,” says Kapil ... >>

Random news from the Archive

Robot conveying emotions while reading 24.03.2022

Scientists from the Faculty of Engineering, Information and Systems of the University of Tsukuba (Japan) have developed a robot assistant for reading text messages. It can help users control their mood when reading upsetting news. This device will improve social interactions as we move towards a world that increasingly uses digital communications.

An emoticon in a text message is a quick and easy way to show your indignation to someone who is late for a scheduled meeting. It often lacks the human element that would accompany a face-to-face explanation or telephone conversation. According to scientists, we are probably more upset by the fact that we, our friends, cannot realize how angry and upset we are when we have to wait for them.

Researchers at the University of Tsukuba in Japan have created a hand-held robot called OMOY, which is equipped with a moving block powered by mechanical components inside its body. By moving the internal center of gravity, the robot can express simulated emotions. The prototype was created for experimental experience - this artificial intelligence is able to read and analyze text messages. It turned out that the text with unpleasant or disappointing news was accompanied by a call to OMOY not to be upset - or even sympathy for the user.

The robots were designed in such a way that they could suppress not only the user's anger, but also other negative interpersonal motives - for example, change thoughts of revenge or similar negative emotions.

Other interesting news:

▪ Electric cars from plastic bottles and flax

▪ quantum apocalypse

▪ Magnetic particles pollute the brain

▪ The smartphone will replace all remote controls

▪ SD-M1912 - new DVD-ROM driver

News feed of science and technology, new electronics

Interesting materials of the Free Technical Library:

▪ site section Color and music installations. Selection of articles

▪ article Technology, industry, transport. Crosswordist's Handbook

▪ article What mammals can see in the ultraviolet? Detailed answer

▪ article Kupena multicolored. Legends, cultivation, methods of application

▪ article Connecting walk-through switches. Encyclopedia of radio electronics and electrical engineering

▪ article Funny cards. Focus secret

Leave your comment on this article:

All languages of this page

Home page | Library | Articles | Website map | Site Reviews