Instructions for labor protection when working on a printing and die-cutting machine with a special device for hot stamping with gold and colorful foil

Free technical library

OCCUPATIONAL SAFETY AND HEALTH
Free library / Occupational Safety and Health / Standard instructions for labor protection

Instructions on labor protection when working on a printing and die-cutting machine with a special device for hot stamping with gold and colorful foil. Full Document

Occupational Safety and Health

Occupational Safety and Health / Standard instructions for labor protection

Comments on the article

Safe Operation

1. General requirements for labor protection

1.1. Persons who have passed a medical examination and have no contraindications to work in this profession (specialty), introductory briefing and briefing at the workplace are allowed to work. Workers are allowed to work independently after an internship, verification of theoretical knowledge and acquired skills in safe ways of working. In the future, at the workplace, briefings on labor protection are held at least once every 3 months.

1.2. When transferring to a new job, from temporary to permanent, from one operation to another with a change in the technological process or equipment, employees must be instructed in labor protection at the workplace.

1.3. Conducting all types of briefings must be recorded in the Briefing Log with the obligatory signatures of the person who received and conducted the briefing.

1.4. Each employee is obliged to comply with the requirements of this instruction, labor and production discipline, work and rest regime, all requirements for labor protection, safe work performance, industrial sanitation, fire safety, electrical safety.

1.5. Smoking is allowed only in specially designated areas. The use of alcoholic beverages at work, as well as going to work in a state of alcoholic or drug intoxication, is prohibited.

1.6. When performing work, it is necessary to be attentive, not to be distracted by extraneous affairs and conversations, and not to distract others from work. It is forbidden to sit down and lean on random objects and fences.

1.7. It is not allowed to approach operating machines, installations, machines on which other workers work, and distract them with extraneous conversations, turn on or off (except in emergency cases) equipment, transport and lifting mechanisms, work on which is not assigned, go beyond the fences of hazardous areas, in the zones of technological passages.

1.8. The employer is obliged to provide workers with overalls, safety shoes, as well as personal protective equipment in accordance with the work they perform and in accordance with applicable standards. It is forbidden to work without overalls, safety shoes and other personal protective equipment laid down in accordance with the standards.

1.9. Each employee needs:

know the place of storage of the workshop first-aid kit;
be able to provide first aid for work-related injuries.

1.10. It is allowed to store and eat food only in established and equipped places.

1.11. It is forbidden to be in production premises in outerwear, undress or hang clothes, hats, bags on equipment.

1.12. Do not clutter up passages, driveways, workplaces, approaches to shields with fire fighting equipment, fire hydrants and a general switch.

1.13. Spilled cleaners, lubricants, water, etc. on the floor. wipe off immediately.

1.14. Cleaning materials impregnated with oil, paint, solvent, put in tightly closed metal boxes. Do not scatter these materials, at the end of the shift they should be removed from the premises.

1.15. Store fuels, lubricants and flammable liquids only in a tightly closed metal container (box) or cabinet in an amount not exceeding the replacement rate. Joint storage of acids and flammable and combustible liquids (gasoline, toluene, alcohol, kerosene, white spirit, etc.) is prohibited. Store chemicals in quantities not exceeding the established norms, in a tightly closed container with an inscription on the contents.

1.16. It is forbidden to repair equipment, fix electrical equipment and the electrical network to personnel who do not have access to these works, work near unshielded current-carrying parts, touch electrical wires, general lighting fittings, open doors of electrical cabinets, fencing of knife switches, switchboards and control panels.

1.17. Do not use lubricants for washing hands.

1.18. It is forbidden to be in the production room after the end of work.

1.19. The employee is responsible in accordance with applicable law for compliance with the requirements of instructions, industrial injuries and accidents that occurred through his fault.

1.20. The control of the implementation of this instruction is assigned to the head of the department.

2. Safety requirements before starting work

2.1. Put on your uniform, put it in order.

2.2. Familiarize yourself with the entries in the Journal of the technical condition of the equipment. In case of any comments, do not start work until the troubleshooting and a note in the journal (adjuster, electrician) about the health of the equipment.

2.3. Inspect equipment and work area. Prepare all necessary equipment and tools for work. Check their correctness. Remove all unnecessary items from the machine (oil cans, rags, etc.).

2.4. Check the serviceability of the machine, heating elements, thermostats, switching devices on and off, brakes and blocking operation by turning the safety bar (when the safety device is activated, the crucible must stop at a distance of at least 5 cm from the printing plate); the presence and rigidity of the fastening of the flywheel guards, belt drive, gears and push-button control; the correctness and reliability of the conclusion of the form, the stamp in the frame and fixing them on the machine; the strength of the fastening of the rollers in the nests, the presence of protective grounding, cleanliness and order in the workplace.

2.5. Check whether the local exhaust and general supply and exhaust ventilation systems are turned on (ventilation should be turned on 10 - 15 minutes before starting work).

2.6. Check and adjust workplace lighting.

2.7. Immediately inform the supervisor of the noticed shortcomings and malfunctions at the workplace and do not start work until the troubleshooting and permission of the master.

3. Safety requirements during work

3.1. Install the printing plate (stamp), replace the failed signal lamps, perform seasoning and all ancillary work (adjustment, cleaning, lubrication, etc.) with the machine turned off.

3.2. Before putting the machine into operation, check that no service or maintenance personnel is in the danger area.

3.3. Before starting the machine, give a warning signal, and then make a few turns, make sure that the machine is working normally.

3.4. It is forbidden:

work on faulty equipment;
embossing on raw materials;
work without sufficient lighting of the workplace;
leave unattended the machine, included in the working stroke;
work on equipment with guards removed and faulty interlocks.

3.5. During the operation of the machine, it is prohibited:

correct an incorrectly placed sheet, postcard, cardboard, etc.;
remove from the printing plate (stamp) a sheet, postcard, cardboard, etc. adhering to it;
install foil rolls on holders and adjust the amount of foil feed;
check the fastening of the stamps;
pick up sheets of paper, postcards, cardboard, etc. that have fallen into the machine and under it;
adjust, lubricate, clean and troubleshoot the machine;
wipe stamps (printed form);
stand close to the fences of the machine and lean on them;
touch the moving parts of the machine, stick your hands into the danger zone, i.e. for the guard rail.

4. Safety requirements in emergency situations

4.1. In case of fire, immediately turn off the machine, turn off the power supply, with the exception of the lighting network, call the fire brigade, inform the work manager and proceed to extinguish the fire using the available fire extinguishing equipment.

4.2. If voltage (feeling of current) is detected on the metal parts of the machine, the electric motor hums, in case of vibration or increased noise, with a sharp heating of the electric wires, the electric motor, a decrease in the number of revolutions of the electric motor shaft, sparking in electrical equipment, a break in the ground wire, stop the machine, report the malfunction to the foreman and without his instructions, do not start work.

4.3. Stop the equipment and disconnect it from the mains when:

interruption of the supply of electricity;
traumatic situation;
ingress of foreign objects into the equipment;
poor fixing of the printed form (stamp);
malfunctions of equipment, safety, protective, blocking, starting, including, etc. devices.

4.4. In case of injury, first of all, release the victim from the traumatic factor, call for medical assistance, provide first aid to the victim, notify the work manager and save the traumatic situation until the causes of the incident are investigated.

5. Safety requirements at the end of work

5.1. Turn off the equipment, remove tools and fixtures to the designated places, tidy up the workplace. Make an entry in the Log about the status of the equipment.

5.2. Take off your overalls, put them in the closet.

5.3. Wash hands and face thoroughly with warm water and soap.

We recommend interesting articles Section Standard instructions for labor protection:

▪ Operation of wells equipped with rod pumping units. Standard instruction on labor protection

▪ Heating service technician. Standard instruction on labor protection

▪ Work on steam sterilizers VK-30. Standard instruction on labor protection

See other articles Section Standard instructions for labor protection.

Read and write useful comments on this article.

<< Back

Latest news of science and technology, new electronics:

Artificial leather for touch emulation 15.04.2024

In a modern technology world where distance is becoming increasingly commonplace, maintaining connection and a sense of closeness is important. Recent developments in artificial skin by German scientists from Saarland University represent a new era in virtual interactions. German researchers from Saarland University have developed ultra-thin films that can transmit the sensation of touch over a distance. This cutting-edge technology provides new opportunities for virtual communication, especially for those who find themselves far from their loved ones. The ultra-thin films developed by the researchers, just 50 micrometers thick, can be integrated into textiles and worn like a second skin. These films act as sensors that recognize tactile signals from mom or dad, and as actuators that transmit these movements to the baby. Parents' touch to the fabric activates sensors that react to pressure and deform the ultra-thin film. This ... >>

Petgugu Global cat litter 15.04.2024

Taking care of pets can often be a challenge, especially when it comes to keeping your home clean. A new interesting solution from the Petgugu Global startup has been presented, which will make life easier for cat owners and help them keep their home perfectly clean and tidy. Startup Petgugu Global has unveiled a unique cat toilet that can automatically flush feces, keeping your home clean and fresh. This innovative device is equipped with various smart sensors that monitor your pet's toilet activity and activate to automatically clean after use. The device connects to the sewer system and ensures efficient waste removal without the need for intervention from the owner. Additionally, the toilet has a large flushable storage capacity, making it ideal for multi-cat households. The Petgugu cat litter bowl is designed for use with water-soluble litters and offers a range of additional ... >>

The attractiveness of caring men 14.04.2024

The stereotype that women prefer "bad boys" has long been widespread. However, recent research conducted by British scientists from Monash University offers a new perspective on this issue. They looked at how women responded to men's emotional responsibility and willingness to help others. The study's findings could change our understanding of what makes men attractive to women. A study conducted by scientists from Monash University leads to new findings about men's attractiveness to women. In the experiment, women were shown photographs of men with brief stories about their behavior in various situations, including their reaction to an encounter with a homeless person. Some of the men ignored the homeless man, while others helped him, such as buying him food. A study found that men who showed empathy and kindness were more attractive to women compared to men who showed empathy and kindness. ... >>

Random news from the Archive

Monochrome Epson Printing Factory 16.03.2014

In any company there is always a need for printing, so the question arises of choosing a printer. Most often, laser printers are chosen for the office, because it is believed that they work faster and better. Epson, which developed its "Monochrome Print Factory", debunks the prevailing stereotypes and offers a more profitable solution.

Fast and economical printing is the key to high-quality document management in any company. Although the market for printing devices offers many solutions in various price categories, the problem of choosing a printer is still relevant. And one of the main questions that arise before buying is which printer to choose - inkjet or laser?

If we trace the trend in the use of devices by type (laser or inkjet), then, according to stable stereotypes, laser printers are most often chosen for office needs. But laser devices require expensive toners and higher energy consumption, so there is no question of saving in practice. Many consumers tend to believe that the purchased expensive device will at least print quickly. But is it really so?

Epson has been developing an alternative to laser devices for a long time and was able to offer the market a unique line of original printers without cartridges - the Epson Monochrome Print Factory, which includes both printers: Epson M100 and Epson M105, and Epson M200 MFP. Thanks to the large built-in 140 ml ink tanks, Epson managed to reduce the cost of an A4 print to a record 15 kopecks using original consumables - this is three times cheaper than a print of the same format on a laser printer using refillable toner.

The starter set of consumables for the "Epson Monochrome Print Factory" is enough for 11 thousand prints, while the laser "brothers" have only 1500. And this means a long-term benefit for customers, because due to the high resource of the starter set of consumables and the low cost of a print, the cost ownership of "Epson Mono Print Factory" for three years is more than half that of a laser printer.

Often, the main criterion for choosing a laser printer is high print quality. "Epson Monochrome Printing Factory" uses pigment inks, which provide high-definition printing and print durability even on plain paper - the print does not smear or spread from accidental water ingress, it can be highlighted with a marker without compromising quality.

As for the print speed, the Epson Print Factory is also all right with this. Inkjet printers have always boasted a fast first page out because they don't have to spend time warming up. There is also a special draft mode to increase typing speed.

In recent years, more and more attention has been paid to the protection of the environment. It has become a real trend. All Epson Print Factory products are designed to comply with environmental regulations and be friendly to the environment. Thus, inkjet printing technology provides less energy consumption, and consumables - greater environmental friendliness compared to laser printing, pigment inks, unlike toner cartridges, are not toxic.

Other interesting news:

▪ Mathematics of canine beauty

▪ diamond plow

▪ LCD monitors and TVs are getting cheaper

▪ Heavy duty wood

▪ Samsung Level U Premium Bluetooth Headset

News feed of science and technology, new electronics

Interesting materials of the Free Technical Library:

▪ section of the site Winged words, phraseological units. Selection of articles

▪ article Olympus. Popular expression

▪ Article How does our diet affect us? Detailed answer

▪ article Senior machinist of turbine equipment. Standard instruction on labor protection

▪ article Connecting the DVR to the car's on-board network. Encyclopedia of radio electronics and electrical engineering

▪ article Glass and enamel. Chemical Experience

Leave your comment on this article:

All languages of this page

Home page | Library | Articles | Website map | Site Reviews