Job description for an extruder operator

Free technical library

JOB INSTRUCTIONS
Free library / Occupational Safety and Health / Job descriptions

Job description for an extruder operator. Full document

Occupational Safety and Health

Occupational Safety and Health / Job descriptions

Comments on the article

I. General Provisions

The extruder operator reports directly to _______.
The extruder operator follows the instructions of _______.
The extruder operator replaces _______.
The extruder operator is replaced by _______.
The extruder driver is appointed to the position and dismissed by the head of the department in agreement with the head of the department.
Must know:

the technology of the extrusion process and the rules for its regulation;
device and principle of operation of the serviced equipment;
rules for the use of control and measuring devices and tools;
physical and chemical properties of the raw materials used;
requirements for the quality of manufactured materials and products.

When transferring to another job or dismissal from office, the Extruder Operator is responsible for the proper and timely handover of cases to the person taking on this position, and in the absence of such, to the person replacing him or directly to his supervisor.

II. Official duties

The extruder machinist performs the following job responsibilities:

Managing the manufacturing process and calibration on extruders and extrusion rotary automated lines of profiles of complex section (hollow, monolithic, flat, corrugated types PPO-4, PPO-21, PPO-23, PPO-24, PPO-25), decorative overlays, skids , films and products from them, sheets, artificial threads and bristles, pipes with a diameter of up to 110 mm and other products made of PVC, polystyrene, polyethylene and other mixtures.
Preparing the extruder for operation: cleaning, selection and installation of the head and die, setting the head gaps, heating the cylinder and head zones to the specified temperature.
Adjustment of extruder units under the guidance of an extruder operator of higher qualification for the specified parameters: extruder, blowing, cutting and receiving-winding devices, cooling system and instrumentation.
Preparation of used devices and tools.
Preparation of the mixture for extrusion and its periodic loading into the extruder.
Ensuring the synchronous operation of the extruder units and the extrusion rotary line under the guidance of a more highly qualified extruder operator.
Regulation of the number of revolutions of the screw, the thickness of the material, the operation of the winding and cutting mechanisms.
Control over the established technological regime according to the indications of instrumentation.
Periodic control over the compliance of manufactured materials and products with samples and drawings.
Removal of finished products and bobbins with finished materials from the winder.
Weighing, marking of finished products and products, their transfer for sorting, sorting, packaging.

III. Rights

The extruder operator has the right to:

give assignments to subordinate employees, tasks on a range of issues included in his functional duties.
control the fulfillment of production tasks, the timely execution of individual orders by subordinate employees.
request and receive the necessary materials and documents related to the issues of its activities and the activities of employees subordinate to it.
interact with other services of the enterprise on production and other issues that are part of its functional duties.
get acquainted with the draft decisions of the management of the enterprise regarding the activities of the Division.
propose for consideration by the manager proposals for improving the work related to the duties provided for in this Job Description.
submit for consideration by the head of the proposal on the promotion of distinguished employees, the imposition of penalties on violators of production and labor discipline.
report to the manager on all identified violations and shortcomings in connection with the work performed.

IV. A responsibility

The extruder operator is responsible for:

improper performance or non-performance of their official duties provided for by this Job Description - within the limits determined by the labor legislation of Ukraine.
violation of the rules and regulations governing the activities of the enterprise.
offenses committed in the course of carrying out their activities - within the limits determined by the current administrative, criminal and civil legislation of Ukraine.
causing material damage - within the limits determined by the current labor and civil legislation of Ukraine.
compliance with current instructions, orders and orders for the preservation of trade secrets and confidential information.
compliance with internal regulations, safety and fire safety rules.

We recommend interesting articles Section Job descriptions:

▪ Land surveyor of the city administration. Job description

▪ Transportation manager. Job description

▪ Washing machine operator. Job description

See other articles Section Job descriptions.

Read and write useful comments on this article.

<< Back

Latest news of science and technology, new electronics:

Machine for thinning flowers in gardens 02.05.2024

In modern agriculture, technological progress is developing aimed at increasing the efficiency of plant care processes. The innovative Florix flower thinning machine was presented in Italy, designed to optimize the harvesting stage. This tool is equipped with mobile arms, allowing it to be easily adapted to the needs of the garden. The operator can adjust the speed of the thin wires by controlling them from the tractor cab using a joystick. This approach significantly increases the efficiency of the flower thinning process, providing the possibility of individual adjustment to the specific conditions of the garden, as well as the variety and type of fruit grown in it. After testing the Florix machine for two years on various types of fruit, the results were very encouraging. Farmers such as Filiberto Montanari, who has used a Florix machine for several years, have reported a significant reduction in the time and labor required to thin flowers. ... >>

Advanced Infrared Microscope 02.05.2024

Microscopes play an important role in scientific research, allowing scientists to delve into structures and processes invisible to the eye. However, various microscopy methods have their limitations, and among them was the limitation of resolution when using the infrared range. But the latest achievements of Japanese researchers from the University of Tokyo open up new prospects for studying the microworld. Scientists from the University of Tokyo have unveiled a new microscope that will revolutionize the capabilities of infrared microscopy. This advanced instrument allows you to see the internal structures of living bacteria with amazing clarity on the nanometer scale. Typically, mid-infrared microscopes are limited by low resolution, but the latest development from Japanese researchers overcomes these limitations. According to scientists, the developed microscope allows creating images with a resolution of up to 120 nanometers, which is 30 times higher than the resolution of traditional microscopes. ... >>

Air trap for insects 01.05.2024

Agriculture is one of the key sectors of the economy, and pest control is an integral part of this process. A team of scientists from the Indian Council of Agricultural Research-Central Potato Research Institute (ICAR-CPRI), Shimla, has come up with an innovative solution to this problem - a wind-powered insect air trap. This device addresses the shortcomings of traditional pest control methods by providing real-time insect population data. The trap is powered entirely by wind energy, making it an environmentally friendly solution that requires no power. Its unique design allows monitoring of both harmful and beneficial insects, providing a complete overview of the population in any agricultural area. “By assessing target pests at the right time, we can take necessary measures to control both pests and diseases,” says Kapil ... >>

Random news from the Archive

Miniature Digital MEMS Microphone MP43DT05 26.08.2018

STMicroelectronics' new MP34DT05TR-A digital microphone is designed for audio applications that require small footprint, high sound quality and wide dynamic range. The MP34DT05TR-A features a high sensitivity of -26 dBFS +-3 dB and a good signal-to-noise ratio of 64 dB.

The top entry port simplifies PCB design as no hole under the microphone is required to receive sound pressure. Due to the internal processing of the analog signal, a device with a digital microphone is less susceptible to interference and interference.

The MP34DT05TR-A microphone operates at 1,6V to 3,6V and has a low consumption of 650µA. The output signal is a PDM digital stream with a clock frequency of 1,2 to 3,25 MHz (set by the host). The microphone has an almost linear frequency response in the range from 100 to 10 Hz.

MEMS technology provides reliable microphone performance in a variety of automotive applications for voice control, as well as in industrial applications where operating conditions require high overload capacity and mechanical strength. MEMS technology reduces the size of the microphone, while the output can be either analog or digital.

Microphones based on MEMS technology provide excellent sound quality. They are less sensitive to mechanical vibrations, temperature changes and electromagnetic interference than traditional microphones. The MEMS process makes these mics the perfect stereo solution wherever two or more perfectly matched mics are required. MEMS microphones are omnidirectional, which means they are equally sensitive to sound coming from any direction in space. A wide frequency range makes it possible to use a MEMS microphone as a vibration sensor, including in the ultrasonic range.

Other interesting news:

▪ Flexible material for pulse sensors

▪ Found a way to increase brain tissue by 20 times

▪ A camera with a resolution of 1 GPU has been developed

▪ Effect of stress on brain structure

▪ Fast SanDisk USB 3.1 Type-C SSDs

News feed of science and technology, new electronics

Interesting materials of the Free Technical Library:

▪ section of the site History of technology, technology, objects around us. Article selection

▪ article Go under the window, wander under the window. Popular expression

▪ Article When do strikes start? Detailed answer

▪ article Lakonos berry. Legends, cultivation, methods of application

▪ article Music CD player. Encyclopedia of radio electronics and electrical engineering

▪ article Two antennas on one cable. Encyclopedia of radio electronics and electrical engineering

Leave your comment on this article:

All languages of this page

Home page | Library | Articles | Website map | Site Reviews