Laser pointer in the actuator. Encyclopedia of radio electronics and electrical engineering

Encyclopedia of radio electronics and electrical engineering / Electronics in everyday life

 Comments on the article

Laser pointers, which have recently appeared on sale, are intended primarily for teachers of educational institutions to use them when explaining graphic materials. However, such a pointer can also be used in everyday life, for example, for remote control of the operation of electrical and radio appliances. How to do this is described in the published article. A laser pointer, despite its outward simplicity, is a relatively complex product. It contains a semiconductor laser, automatic maintenance of a certain current flowing through it, an optical system, a battery of galvanic cells with a voltage of 3 ... 4,5 V, and a power button.

The current consumed by the laser is 30...50 mA. Although the power emitted by the pointer (wavelength 630...650 nm) does not exceed 5 mW, due to its concentration in a narrow beam, propagation losses are small. Laser radiation can be fixed at a great distance. However, it is strictly forbidden to direct the pointer beam at the eyes - this is dangerous. The pointer can work in security devices, light phones, home-made toys, bird scaring devices, etc. For now, we will limit ourselves to a story about the construction of an automaton capable of turning on and off household electrical and radio appliances at the signal of the pointer. The pointer itself does not require any alteration.

Rice. 1 (click to enlarge)

The automaton (Fig. 1) contains a photodetector on a photodiode VD1, a voltage comparator on logic elements DD1.1, DD1.2, a pulse generator on elements DD1.3, DD1.4, a D-trigger DD2, two electronic switches on transistors VT1, VT2 , actuating element - electromagnetic relay K1 and power supply. The power supply is made according to a transformerless circuit with a quenching capacitor Sat. The alternating voltage is rectified by diodes VD6, VD7, smoothed by capacitor C5 and stabilized by zener diodes VD4, VD5. Power is supplied to the microcircuits from the VD4 zener diode through the VD2 diode and the smoothing capacitor C 1.

The device works like this. At the initial moment of time, after connecting the device to the network, a high logic level through the C4R7 chain enters the input R of the trigger and resets it. The trigger output is a low logic level, the key on the transistor VT2 is closed, the relay is de-energized, the load is disconnected from the network. At the input and output of the comparator there will be a high logic level, and at the inputs of the elements DD1.3, DD1.4 - low, the generator is not working. At the same time, a high level is set at the output of the DD1.4 element, the transistor VT1 opens and turns on the HL1 LED.

How does the switch take place? The photodiode VD1 is illuminated with a laser beam, and the voltage across it is significantly reduced. The comparator, after discharging the capacitor C2, is triggered, and a low level appears at its output. A high level is supplied to the outputs of the elements DD1.3, DD1.4, the generator starts to work, the LED blinks, indicating that the photodiode is illuminated. If we now turn off the laser or move the beam away from the photodiode, then the voltage on it will increase, the comparator will be set to a high output level, and the trigger will switch. A high logic level will appear at its output, the transistor VT2 will open, the relay will work and the closing contacts K1.1 will supply the mains voltage to the load. In the case of repeated short-term illumination of the photodiode (until the LED blinks), the device will switch to its original state and the load will be de-energized.

Thanks to the use of a relay, it is permissible to connect a wide variety of electronic equipment to the device: radios, TVs, VCRs, etc. with any power supplies, as well as electrical appliances with electric motors, such as fans.

Fig. 2

All parts of the device, except for the relay and the VD3 diode, are placed on a printed circuit board (Fig. 2) made of one-sided foil fiberglass. It is designed to use transistors KT315A-KT315E, KT312A-KT312V, KT3102A-KT3102D, microcircuits of the K 176, K561, 564 series, any LED from the AL307 series (preferably in a plastic case). Diodes VD2, VD3 - any rectifier, VD6, VD7 - KD102B or similar low-power ones with a maximum allowable reverse voltage of at least 400 V and a current of at least 100 mA, zener diodes - for a stabilization voltage of 8 ... 10 V. Polar capacitors - series K50, K52, C6 - K73, the rest - KM, KLS, K 10. Trimmer resistor R2 - SPZ-19, constants - MLT, C2-33. The relay should be selected with a response voltage of 12 ... 15 V at a current of not more than 30 mA, for example, RES9 (passport RS4.524.200, RS4.524.201), its contacts must withstand the mains voltage and the current consumed by the load.

A few words about the RES9 relay. According to the reference data, its contacts are designed for a voltage of 115 V. However, the long-term practice of using the relay in various devices has shown reliable operation of the contacts at a mains voltage of 220 V. Of course, you can opt for relays of the RKN, MKU-48 types, but the design dimensions will increase significantly.

The board together with the relay is placed in a case of suitable dimensions, made of insulating material. The photodiode and the LED are placed in the openings of the case side by side so that the LED serves as a guide and signals with its flashes that the laser beam hits the photodiode. To avoid interference and malfunctions, you need to install the machine so that the photodiode is protected from light from lighting devices. Setting up the device comes down to setting its sensitivity (with a tuning resistor R2), the speed of response to laser illumination (by selecting capacitor C2), the blinking frequency of the LED (roughly by selecting capacitor C3, smoothly by resistor R5).

The automaton can be somewhat simplified by eliminating the generator. In this case, the output of the resistor R8, left according to the scheme, must be disconnected from output 3 of the DD1 microcircuit and connected to output 11. The elements R5, C3 are removed, the connection between terminals 2 and 4 of DD1 is removed, and the unused inputs of the elements DD1.3, DD1.4 are connected to the common wire. In this case, when the laser beam hits the photodiode and the comparator is triggered, the LED will go out.

Fig. 3

A variant of a simpler machine is possible (Fig. 3), if it uses sensitive trinistors 2U107A-2U107E, which open at a small (less than a volt) voltage on the control electrode and a small (several microamperes) current in its circuit. Its basis is a trigger on trinistors VS1.VS2, which is powered, as in the previous design, from a block with a quenching capacitor. Let's analyze the operation of the machine. After connecting it to the network, both trinistors will be closed, and the relay will be de-energized.

If you illuminate the photodiode VD2 with a laser beam, then due to the photoelectric effect, a voltage will appear on it, which will go to the control electrode of the trinistor VS2, and it will open. The relay will work and turn on the load in the network - this will be signaled by the illuminated HL2 LED. Capacitor C1 will start charging (minus on the right output according to the diagram). To turn off the load, illuminate the photodiode VD1. In this case, the trinistor VS1 opens, including the HL1 LED. The trinistor VS2 closes, since a negative voltage from the capacitor C1 is briefly applied to its anode. The relay is de-energized, the HL2 LED goes out, the load is disconnected from the network.

If now the photodiode VD2 is illuminated again, the trinistor VS2 will open, and VS1 will close, since a negative voltage from the capacitor C1 will be applied to its anode. The load will be energized. Experiments have shown that AL360A, AL360B LEDs work well as a photodiode in this machine, since they are based on IR emitting diodes. In addition, they are equipped with a focusing reflector, which increases their sensitivity to the laser radiation of the pointer.

 
Fig. 4

The details of the machine are designed to work with the RES9 relay (passport RS4.524.200). They can be placed in a small housing (Fig. 4) made of insulating material. Holes for LEDs and photodiodes are drilled on the front wall of the case, and a power outlet is installed on the back.

When setting up the machine, a capacitor C3 and a zener diode are preliminarily selected. The stabilization voltage of the zener diode should be approximately 4 ... 5 V more than the relay operation voltage, and the capacitance of the capacitor should be such that the current through the relay is 15 ... 20 mA more than its operation current. The disadvantage of the machine is its low sensitivity, which limits its control range. When setting up the machine, electrical safety measures should be observed, since its parts are galvanically connected to the network. All soldering should be done only with the machine disconnected from the network.

Author: I. Nechaev, Kursk; Publication: cxem.net

See other articles Section Electronics in everyday life.

Read and write useful comments on this article.

<< Back

Latest news of science and technology, new electronics:

Machine for thinning flowers in gardens 02.05.2024

In modern agriculture, technological progress is developing aimed at increasing the efficiency of plant care processes. The innovative Florix flower thinning machine was presented in Italy, designed to optimize the harvesting stage. This tool is equipped with mobile arms, allowing it to be easily adapted to the needs of the garden. The operator can adjust the speed of the thin wires by controlling them from the tractor cab using a joystick. This approach significantly increases the efficiency of the flower thinning process, providing the possibility of individual adjustment to the specific conditions of the garden, as well as the variety and type of fruit grown in it. After testing the Florix machine for two years on various types of fruit, the results were very encouraging. Farmers such as Filiberto Montanari, who has used a Florix machine for several years, have reported a significant reduction in the time and labor required to thin flowers. ... >>

Advanced Infrared Microscope 02.05.2024

Microscopes play an important role in scientific research, allowing scientists to delve into structures and processes invisible to the eye. However, various microscopy methods have their limitations, and among them was the limitation of resolution when using the infrared range. But the latest achievements of Japanese researchers from the University of Tokyo open up new prospects for studying the microworld. Scientists from the University of Tokyo have unveiled a new microscope that will revolutionize the capabilities of infrared microscopy. This advanced instrument allows you to see the internal structures of living bacteria with amazing clarity on the nanometer scale. Typically, mid-infrared microscopes are limited by low resolution, but the latest development from Japanese researchers overcomes these limitations. According to scientists, the developed microscope allows creating images with a resolution of up to 120 nanometers, which is 30 times higher than the resolution of traditional microscopes. ... >>

Air trap for insects 01.05.2024

Agriculture is one of the key sectors of the economy, and pest control is an integral part of this process. A team of scientists from the Indian Council of Agricultural Research-Central Potato Research Institute (ICAR-CPRI), Shimla, has come up with an innovative solution to this problem - a wind-powered insect air trap. This device addresses the shortcomings of traditional pest control methods by providing real-time insect population data. The trap is powered entirely by wind energy, making it an environmentally friendly solution that requires no power. Its unique design allows monitoring of both harmful and beneficial insects, providing a complete overview of the population in any agricultural area. “By assessing target pests at the right time, we can take necessary measures to control both pests and diseases,” says Kapil ... >>

Random news from the Archive Smart material for camouflage 29.06.2015 The University of Bristol has created a "smart material" for camouflage that works on a principle borrowed from squid. Squids are masters of changing their coloration depending on the background. This ability is provided to them by specialized cells with pigments - chromatophores. Scientists at the University of Bristol have replicated the principle behind squid camouflage by creating a "smart material" that could potentially be used in camouflage or dynamically patterned clothing. The material on an elastic dielectric basis resembles skin. The cells that form it have the ability to change their state depending on the state of neighboring cells, as a result of which the color of the material changes. So far, cells can only open and close, but this is enough to demonstrate the fundamental efficiency of the idea. Scientists expect to develop the idea and teach the material to form patterns described by certain rules. As a practical application of the new material, camouflage and the transmission of visual signals are named.

Other interesting news:

▪ Scientific companies of Russia

▪ artificial blood transfusion

▪ Coffee in test tubes

▪ Laser shoe fitting

▪ Acoustic sensors on military helmets will detect snipers

News feed of science and technology, new electronics

Interesting materials of the Free Technical Library:

▪ site section Preamplifiers. Article selection

▪ article Keep your nose to the wind. Popular expression

▪ article How did rivers appear? Detailed answer

▪ article Handling oxygen and acetylene cylinders. Standard instruction on labor protection

▪ article Ignition system for a car with a new method of fuel ignition. Encyclopedia of radio electronics and electrical engineering

▪ article Wiring. External wiring. Encyclopedia of radio electronics and electrical engineering

Leave your comment on this article:

All languages ​​of this page

Arabic	Hebrew	Polish
Bengali	Hindi	Portuguese
Chinese	Italian	Spanish
English	Japanese	Turkish
French	Korean	Ukrainian
German	Malay	Vietnamese

Home page | Library | Articles | Website map | Site Reviews

www.diagram.com.ua
2000-2024